Nissan Rogue. Manual — part 252
DAS
REAR VIEW CAMERA WASHER CONTROL UNIT
DAS-179
< REMOVAL AND INSTALLATION >
[DRIVER ASSISTANCE SYSTEM]
C
D
E
F
G
H
I
J
K
L
M
B
N
P
A
REAR VIEW CAMERA WASHER CONTROL UNIT
Exploded View
INFOID:0000000011277348
Removal and Installation
INFOID:0000000011277349
REMOVAL
1. Remove the luggage rear plate. Refer to
INT-37, "LUGGAGE REAR PLATE : Removal and Installation"
2. Disconnect the harness connector from the rear view camera washer control unit.
3. Remove the rear view camera washer control unit nuts.
4. Remove the rear view camera washer control unit.
INSTALLATION
Installation is in the reverse order of removal.
1.
Body panel
2.
Rear view camera washer control unit
ALOIA0240ZZ
DAS-180
< PRECAUTION >
[CHASSIS CONTROL]
PRECAUTIONS
PRECAUTION
PRECAUTIONS
Precaution for Supplemental Restraint System (SRS) "AIR BAG" and "SEAT BELT
PRE-TENSIONER"
INFOID:0000000011277350
The Supplemental Restraint System such as “AIR BAG” and “SEAT BELT PRE-TENSIONER”, used along
with a front seat belt, helps to reduce the risk or severity of injury to the driver and front passenger for certain
types of collision. Information necessary to service the system safely is included in the SR and SB section of
this Service Manual.
WARNING:
• To avoid rendering the SRS inoperative, which could increase the risk of personal injury or death in
the event of a collision which would result in air bag inflation, all maintenance must be performed by
an authorized NISSAN/INFINITI dealer.
• Improper maintenance, including incorrect removal and installation of the SRS, can lead to personal
injury caused by unintentional activation of the system. For removal of Spiral Cable and Air Bag
Module, see the SR section.
• Do not use electrical test equipment on any circuit related to the SRS unless instructed to in this
Service Manual. SRS wiring harnesses can be identified by yellow and/or orange harnesses or har-
ness connectors.
PRECAUTIONS WHEN USING POWER TOOLS (AIR OR ELECTRIC) AND HAMMERS
WARNING:
• When working near the Airbag Diagnosis Sensor Unit or other Airbag System sensors with the Igni-
tion ON or engine running, DO NOT use air or electric power tools or strike near the sensor(s) with a
hammer. Heavy vibration could activate the sensor(s) and deploy the air bag(s), possibly causing
serious injury.
• When using air or electric power tools or hammers, always switch the Ignition OFF, disconnect the
battery and wait at least three minutes before performing any service.
Precaution for Work
INFOID:0000000011277351
• When removing or disassembling each component, be careful not to damage or deform it. If a component
may be subject to interference, be sure to protect it with a shop cloth.
• When removing (disengaging) components with a screwdriver or similar tool, be sure to wrap the component
with a shop cloth or vinyl tape to protect it.
• Protect the removed parts with a shop cloth and prevent them from being dropped.
• Replace a deformed or damaged clip.
• If a part is specified as a non-reusable part, always replace it with a new one.
• Be sure to tighten bolts and nuts securely to the specified torque.
• After installation is complete, be sure to check that each part works properly.
• Follow the steps below to clean components:
- Water soluble dirt:
• Dip a soft cloth into lukewarm water, wring the water out of the cloth and wipe the dirty area.
• Then rub with a soft, dry cloth.
- Oily dirt:
• Dip a soft cloth into lukewarm water with mild detergent (concentration: within 2 to 3%) and wipe the dirty
area.
• Then dip a cloth into fresh water, wring the water out of the cloth and wipe the detergent off.
• Then rub with a soft, dry cloth.
- Do not use organic solvent such as thinner, benzene, alcohol or gasoline.
- For genuine leather seats, use a genuine leather seat cleaner.
DAS
PRECAUTIONS
DAS-181
< PRECAUTION >
[CHASSIS CONTROL]
C
D
E
F
G
H
I
J
K
L
M
B
N
P
A
Precautions for Harness Repair
INFOID:0000000011277352
• Solder the repaired area and wrap tape around the soldered area.
NOTE:
A fray of twisted lines must be within 110 mm (4.33 in).
• Bypass connection is never allowed at the repaired area.
NOTE:
Bypass connection may cause CAN communication error. The
spliced wire becomes separated and the characteristics of twisted
line are lost.
• Replace the applicable harness as an assembly if error is detected on the shield lines of CAN communica-
tion line.
Precautions for Chassis control
INFOID:0000000011277353
• Do not disassemble the chassis control module.
• Do not reuse if the chassis control module has been dropped.
• Do not perform ACTIVE TEST while driving the vehicle.
• Slight vibrations are felt on the brake pedal and the operation noises occur, when Active Trace Control and
Active Ride Control function operates. This is not a malfunction because it is caused by the functions that
are normally operated.
• Tachometer will rise and engine noise may be noticeable during Active Engine Brake function operation.
This is not a malfunction because it is caused by the function that is normally operated.
• Active Trace Control, Active Ride Control and Active Engine Brake are not always activated in any driving
conditions.
SKIB8766E
SKIB8767E
DAS-182
< PREPARATION >
[CHASSIS CONTROL]
PREPARATION
PREPARATION
PREPARATION
Special Service Tool
INFOID:0000000011277354
The actual shape of the tools may differ from those illustrated here.
Tool number
(TechMate No.)
Tool name
Description
—
(J-46534)
Trim Tool Set
Removing trim components
AWJIA0483ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст