Nissan Rogue. Manual — part 181
ABS ACTUATOR AND ELECTRIC UNIT (CONTROL UNIT)
BRC-135
< REMOVAL AND INSTALLATION >
[VDC/TCS/ABS]
C
D
E
G
H
I
J
K
L
M
A
B
BRC
N
O
P
• After work is completed, bleed air from brake tube. Refer to
BR-16, "Bleeding Brake System"
• Adjust the neutral position of steering angle sensor. Refer to
.
• Perform calibration of the decel G sensor. Refer to
.
CAUTION:
• To install, use flare nut crowfoot and torque wrench.
• Do not reuse the bushings.
• Replace the ABS actuator if it has been dropped or sustained an impact.
• Do not install actuator by holding harness.
• After installing harness connector in the ABS actuator and electric unit (control unit), make sure
connector is securely locked.
BRC-136
< REMOVAL AND INSTALLATION >
[VDC/TCS/ABS]
VDC OFF SWITCH
VDC OFF SWITCH
Exploded View
INFOID:0000000011401012
Removal and Installation
INFOID:0000000011280678
REMOVAL
1. Remove the instrument lower panel LH. Refer to
IP-23, "Removal and Installation"
.
2. Remove the screws and upper switch carrier from the instrument lower panel LH.
3. Release pawls using suitable tool and remove the VDC OFF
switch from the upper switch carrier.
: Pawl
INSTALLATION
Installation is in the reverse order of removal.
1.
Upper switch carrier
2.
Lower switch carrier
3. Mask
4.
Warning system switch
5.
AWD lock switch
6. Hill descent control switch
7.
Instrument lower panel LH
8.
Automatic back door main switch
9. Automatic back door switch
10. Sport mode switch
11. VDC OFF switch
ALJIA1521ZZ
ALJIA1522ZZ
STEERING ANGLE SENSOR
BRC-137
< REMOVAL AND INSTALLATION >
[VDC/TCS/ABS]
C
D
E
G
H
I
J
K
L
M
A
B
BRC
N
O
P
STEERING ANGLE SENSOR
Exploded View
INFOID:0000000011280679
Removal and Installation
INFOID:0000000011280680
Removal and Installation
1. Remove the spiral cable. Refer to
SR-15, "Removal and Installation"
.
2. Remove screws (A) and then remove steering angle sensor (1).
INSTALLATION
Installation is in the reverse order of removal.
ALHIA0359ZZ
1.
Combination switch
2.
Steering angle sensor
3.
Spiral cable
ALHIA0352ZZ
BRC-138
< REMOVAL AND INSTALLATION >
[VDC/TCS/ABS]
HILL DESCENT CONTROL SWITCH
HILL DESCENT CONTROL SWITCH
Exploded View
INFOID:0000000011395887
Removal and Installation
INFOID:0000000011395888
REMOVAL
1. Remove instrument lower panel LH. Refer to
IP-23, "Removal and Installation"
.
2. Disconnect the harness connectors from the switches.
3. Remove the screws from the upper switch carrier and lower switch carrier.
4. Remove the upper switch carrier and lower switch carrier from the instrument lower panel LH.
5. Release pawls using suitable tool and remove the hill descent
control switch from the lower switch carrier.
: Pawl
INSTALLATION
Install in the reverse order of removal.
1.
Upper switch carrier
2.
Lower switch carrier
3. Mask
4.
Warning system switch
5.
AWD lock switch
6. Hill descent control switch
7.
Instrument lower panel LH
8.
Automatic back door main switch
9. Automatic back door switch
10. Sport mode switch
11. VDC OFF switch
ALJIA1521ZZ
ALJIA1522ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст