Nissan Rogue. Manual — part 180
WHEEL SENSOR
BRC-131
< REMOVAL AND INSTALLATION >
[VDC/TCS/ABS]
C
D
E
G
H
I
J
K
L
M
A
B
BRC
N
O
P
• Do not twist front wheel sensor harness when installing front
wheel sensor. Check that grommet (2) is fully inserted to
bracket (1). Check that front wheel sensor harness is not
twisted after installation.
REAR WHEEL SENSOR
REAR WHEEL SENSOR : Exploded View
INFOID:0000000011280672
FWD
AWD
JPFIC0209ZZ
ALFIA0415ZZ
1.
Rear LH wheel sensor
ALFIA0416ZZ
1.
Rear LH wheel sensor
BRC-132
< REMOVAL AND INSTALLATION >
[VDC/TCS/ABS]
WHEEL SENSOR
REAR WHEEL SENSOR : Removal and Installation
INFOID:0000000011280673
CAUTION:
• Be careful not to damage rear wheel sensor edge and sensor rotor teeth.
• When removing the rear wheel hub and bearing, first remove the rear wheel sensor from the rear
wheel hub and bearing (FWD) or the rear axle housing (AWD). Failure to do so may result in damage
to the rear wheel sensor making the rear wheel sensor inoperative.
• Pull out the rear wheel sensor, being careful to turn it as little as possible. Do not pull on the rear
wheel sensor harness.
• Before installation, check if foreign objects such as iron fragments are adhered to the pick-up part of
the rear wheel sensor or to the inside of the hole in the rear wheel hub and bearing (FWD) or the rear
axle housing (AWD) for the rear wheel sensor, or if a foreign object is caught in the surface of the
sensor rotor. Fix as necessary and then install the rear wheel sensor.
REMOVAL
1. Remove the rear wheel and tire using power tool. Refer to
.
2. Remove the rear wheel sensor bolt.
3. Disconnect the harness connector from the rear wheel sensor.
4. Remove the rear wheel sensor from the wheel hub and bearing (FWD) or the rear axle housing (AWD).
5. Remove the rear wheel sensor harness grommet from the bracket.
6. Remove the bolt, the rear wheel sensor harness, and the rear wheel sensor from the bracket.
INSTALLATION
Installation is in the reverse order of removal.
CAUTION:
• When installing, make sure there is no foreign material such as iron chips on and in the hole in the
rear wheel hub and bearing (FWD) or the rear axle housing (AWD) for the rear wheel sensor. Make
sure no foreign material has been caught in the sensor rotor. Remove any foreign material and clean
the mount.
• Do not twist rear wheel sensor harness when installing rear
wheel sensor. Check that grommet (2) is fully inserted to
bracket (1). Check that rear wheel sensor harness is not
twisted after installation.
JPFIC0209ZZ
SENSOR ROTOR
BRC-133
< REMOVAL AND INSTALLATION >
[VDC/TCS/ABS]
C
D
E
G
H
I
J
K
L
M
A
B
BRC
N
O
P
SENSOR ROTOR
FRONT SENSOR ROTOR
FRONT SENSOR ROTOR : Removal and Installation - Front Sensor Rotor
INFOID:0000000011280674
The front wheel sensor rotor is an integral part of the wheel hub and bearing and cannot be disassembled.
FAX-9, "Removal and Installation"
(FWD) or
FAX-47, "Removal and Installation"
(AWD).
REAR SENSOR ROTOR
REAR SENSOR ROTOR : Removal and Installation - Rear Sensor Rotor
INFOID:0000000011280675
For FWD vehicles, the rear wheel sensor rotor is an integral part of the wheel hub and bearing and cannot be
disassembled. Refer to
RAX-7, "Removal and Installation"
For AWD vehicles, the rear wheel sensor rotor is pressed on the rear drive shaft and can be disassembled.
RAX-21, "Disassembly and Assembly"
(AWD).
BRC-134
< REMOVAL AND INSTALLATION >
[VDC/TCS/ABS]
ABS ACTUATOR AND ELECTRIC UNIT (CONTROL UNIT)
ABS ACTUATOR AND ELECTRIC UNIT (CONTROL UNIT)
Exploded View
INFOID:0000000011280676
Removal and Installation
INFOID:0000000011280677
REMOVAL
CAUTION:
• To remove brake tube, use a flare nut wrench to prevent flare nuts and brake tube from being dam-
aged.
• Do not remove actuator by holding harness.
NOTE:
When removing components such as hoses, tubes/lines, etc., cap or plug openings to prevent fluid from spill-
ing.
1. Disconnect negative battery terminal. Refer to
2. Remove the cowl top cover and cowl top extension. Refer to
EXT-25, "Removal and Installation"
.
3. Separate brake tubes from ABS actuator and electric unit (control unit). Refer to
.
4. Remove the brake booster vacuum hose. Refer to
BR-33, "Removal and Installation"
5. Separate the brake booster vacuum tube and place aside. Refer to
BR-23, "FRONT : Removal and Instal-
.
6. Disconnect the harness connector from the ABS actuator and electric unit (control unit).
7. Remove ABS actuator and electric unit (control unit) bracket bolts and bushings.
8. Remove ABS actuator and electric unit (control unit) from vehicle.
INSTALLATION
Installation is in the reverse order of removal.
1.
ABS actuator and electric unit (control unit) 2.
Connector
3. Bracket
A. To front LH brake caliper
B. To rear RH brake caliper
C. From master cylinder secondary side
D. From master cylinder primary side
E. To rear LH brake caliper
F. To front RH brake caliper
AWFIA1079ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст