Nissan Rogue. Manual — part 563

DRIVE BELTS

EM-17

< PERIODIC MAINTENANCE >

C

D

E

F

G

H

I

J

K

L

M

A

EM

N

P

O

1. Remove the drive belt. Refer to

EM-15, "Removal and Installation"

.

2. Remove the drive belt auto-tensioner.

INSTALLATION

Installation is in the reverse order of removal.

CAUTION:

• Install the drive belt auto-tensioner carefully so not to damage the water pump pulley.

• If there is damage greater than peeled paint, replace the drive belt auto-tensioner.

EM-18

< PERIODIC MAINTENANCE >

AIR CLEANER FILTER

AIR CLEANER FILTER

Exploded View

INFOID:0000000011279939

Removal and Installation

INFOID:0000000011279940

CHANGING THE AIR CLEANER FILTER

1. Remove air duct assembly from air cleaner case (upper).
2. Open the air cleaner case.
3. Remove the air cleaner filter.
4. Install a new air cleaner filter.
5. Close the air cleaner case.
6. Secure the air cleaner case clips.

INSPECTION AFTER REMOVAL

Examine the air cleaner filter for stains, clogging, or damage.

• Remove dirt and foreign objects (such as dead leaves) on air cleaner filter surface and inside cleaner case.

• If clogging or damage is observed, replace the air cleaner filter.

CAUTION:

Do not clean the viscous paper type air cleaner filter by blowing as there is a risk of deterioration of its

performance.

MAINTENANCE INTERVAL

Refer to

MA-7, "Introduction of Periodic Maintenance"

.

1.

Mass air flow sensor

2.

Air cleaner filter

3.

Air cleaner case (lower)

4.

Air duct assembly (aft)

5.

Grommet

6.

Resonator bracket (front)

7.

Resonator bracket (rear)

8.

Resonator

9.

Air duct

10.

Mounting clip

11.

Air duct assembly (fore)

12.

Air duct assembly

13.

Air cleaner bracket

14.

Grommet

15.

Air cleaner case (upper)

A.

To Electric throttle control actuator

Front

AWBIA2315ZZ

SPARK PLUG

EM-19

< PERIODIC MAINTENANCE >

C

D

E

F

G

H

I

J

K

L

M

A

EM

N

P

O

SPARK PLUG

Exploded View

INFOID:0000000011279941

Removal and Installation

INFOID:0000000011279942

REMOVAL

1. Remove air duct assembly.
2. Remove ignition coil. Refer to

EM-41, "Exploded View"

.

3. Remove spark plug using Tool.

INSPECTION AFTER REMOVAL

Visually check the electrode for dirt and wear and the insulator for burning.

1. Ignition coil

2. Spark plug

3. Rocker cover

AWBIA1302GB

Tool number

: — (J-48891)

ALBIA0672GB

(A)

: Iridium alloy

AWBIA1745ZZ

EM-20

< PERIODIC MAINTENANCE >

SPARK PLUG

• Do not use a wire brush for cleaning the spark plugs. Replace as

necessary.

• If plug is covered with carbon, a spark plug cleaner may be used.

• Checking and adjusting plug gap is not required between change

intervals. If the gap is out of specification, replace the spark plug.

CAUTION:

Do not drop or shock plug.

INSTALLATION

Installation is in the reverse order of removal.

*: Always check with the Parts Department for the latest parts information.

SMA773C

Cleaner air pressure : less than 588 kPa (6 kg/cm

2

, 85 psi)

Cleaning time

: less than 20 seconds

SMA806CA

Standard type*

DENSO

FXE20HE11C

Gap (nominal)

1.1 mm (0.043 in)