Nissan Rogue. Manual — part 729
WINDSHIELD GLASS
GW-13
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
J
L
M
A
B
GW
N
O
P
PRIMER
Unit:mm (in.)
INSPECTION
Repairing Water Leaks for Windshield
• Leaks can be repaired without removing and reinstalling glass.
• If water is leaking between the urethane adhesive material and body or glass, determine the extent of leak.
• This can be done by applying water to the windshield area while pushing glass outward.
• To stop the leak, apply primer (if necessary) and then urethane adhesive to the leak point.
AWKIA3177ZZ
1.
Body
2.
Windshield glass molding
3.
Windshield glass
4.
Windshield glass lower molding
5.
Cowl top cover
D.
16 mm (0.63 in)
E.
14 mm (0.55 in)
F.
Primer
GW-14
< REMOVAL AND INSTALLATION >
FRONT DOOR GLASS
FRONT DOOR GLASS
Exploded View
INFOID:0000000011276510
Removal and Installation
INFOID:0000000011276511
REMOVAL
1. Remove the front door finisher. Refer to
INT-15, "Removal and Installation"
2. Remove the front door vapor barrier (1).
3. Temporarily reconnect the main power window and door lock/unlock switch (LH door) or power window
and door lock/unlock switch RH (RH door).
4. Operate the main power window and door lock/unlock switch (LH door) or front door power window motor
and door lock/unlock switch RH (RH door) to raise/lower the front door glass until the front door regulator
to front door glass bolts can be seen.
1. Front door
2.
Front regulator
3.
Front power window motor
4.
Front door glass rear run
5.
Front door glass front run
6.
Front door glass
7.
Front door glass rubber run
AWKIA2912ZZ
ALKIA3488ZZ
FRONT DOOR GLASS
GW-15
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
J
L
M
A
B
GW
N
O
P
5. Remove the front door glass regulator (1) to front door glass
bolts (A).
6. While holding the front door glass, raise it at the rear end and
pull the front door glass out of the sash toward the outside of the
door.
INSTALLATION
Installation is in the reverse order of removal.
CAUTION:
• When the main power window and door lock/unlock switch or front power window and door lock/
unlock switch RH is removed it is necessary to perform the initialization procedure. Refer to
28, "ADDITIONAL SERVICE WHEN REMOVING BATTERY NEGATIVE TERMINAL : Special Repair
.
• Tighten bolts to specification. Refer to
.
FITTING INSPECTION
• Check that the front door glass is fit securely into the glass run groove.
• Lower the front door glass slightly [approximately 10 to 20 mm (0.39 to 0.79) and check that the clearance to
the sash is parallel.If the clearance between the glass and sash is not parallel, loosen the front door glass
regulator bolts, front door glass run channel bolts, and glass and run rail bolts to correct the glass position.
ALKIA3490ZZ
LIIA1687E
GW-16
< REMOVAL AND INSTALLATION >
FRONT REGULATOR
FRONT REGULATOR
Exploded View
INFOID:0000000011276512
Removal and Installation
INFOID:0000000011276513
REMOVAL
1. Remove the front door finisher. Refer to
INT-15, "Removal and Installation"
2. Partially remove the front door vapor barrier (1).
3. Temporarily reconnect the main power window and door lock/unlock switch (LH door) or power window
door lock/unlock switch RH (RH door).
4. Operate the power window and door lock/unlock switch (LH door) or front door power window motor and
door lock/unlock switch RH (RH door) to raise/lower the front door glass until the front door regulator to
front door glass bolts can be seen.
1. Front door panel
2.
Front door regulator
3.
Front door power window motor
4.
Front door glass run rear
5.
Front door glass run front
6.
Front door glass
7.
Front door glass rubber run
AWKIA2912ZZ
ALKIA3488ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст