Nissan Rogue. Manual — part 1257
DIAGNOSIS AND REPAIR WORKFLOW
WW-31
< BASIC INSPECTION >
C
D
E
F
G
H
I
J
K
M
A
B
WW
N
O
P
BASIC INSPECTION
DIAGNOSIS AND REPAIR WORKFLOW
Work Flow
INFOID:0000000011280389
WORK FLOW
DETAILED FLOW
1.
REVIEW CUSTOMER COMPLAINT
Review customer complaint. Try to obtain detailed information about the conditions when the symptom occurs.
>> GO TO 2.
2.
VERIFY THE SYMPTOM
Verify the symptom by performing an operational check. Refer to
>> GO TO 3.
3.
PERFORM TROUBLE DIAGNOSIS BY SYMPTOM
Diagnose the vehicle by performing the appropriate trouble diagnosis. Refer to
.
>> GO TO 4.
4.
REPAIR OR REPLACE MALFUNCTIONING PARTS
Repair or replace the specific parts.
>> GO TO 5.
5.
FINAL CHECK
AWLIA1887GB
WW-32
< BASIC INSPECTION >
DIAGNOSIS AND REPAIR WORKFLOW
Perform a final inspection of the system.
Is the inspection result normal?
YES
>> Inspection End.
NO
>> GO TO 2.
WIPER AND WASHER FUSE
WW-33
< DTC/CIRCUIT DIAGNOSIS >
C
D
E
F
G
H
I
J
K
M
A
B
WW
N
O
P
DTC/CIRCUIT DIAGNOSIS
WIPER AND WASHER FUSE
Description
INFOID:0000000011280390
Diagnosis Procedure
INFOID:0000000011280391
1.
CHECK FUSES
Check that the following fuses are not blown:
Is the fuse blown?
YES
>> Replace the blown fuse after repairing the affected circuit.
NO
>> Inspection End.
Component
Capacity
Fuse No.
Location
Front wiper motor
30A
43
IPDM E/R
Front and rear washer motor
15A
33
Fuse block (J/B)
Component
Capacity
Fuse No.
Location
Front wiper motor
30A
43
IPDM E/R
Front and rear washer motor
15A
33
Fuse block (J/B)
WW-34
< DTC/CIRCUIT DIAGNOSIS >
FRONT WIPER MOTOR LO CIRCUIT
FRONT WIPER MOTOR LO CIRCUIT
Component Function Check
INFOID:0000000011280392
1.
CHECK FRONT WIPER LO OPERATION
CONSULT ACTIVE TEST
1. Select “FRONT WIPER” in “Active Test” of “IPDM E/R”.
2. Check front wiper operation.
Is the inspection result normal?
YES
>> Front wiper motor LO circuit is normal.
NO
>> Refer to
.
Diagnosis Procedure
INFOID:0000000011280393
Regarding Wiring Diagram information, refer to
.
1.
CHECK FRONT WIPER MOTOR FUSE
1. Turn the ignition switch OFF.
2. Check that the following fuse is not blown:
Is the fuse blown?
YES
>> Replace the blown fuse after repairing the affected circuit.
NO
>> GO TO 2.
2.
CHECK FRONT WIPER MOTOR (LO) OUTPUT VOLTAGE
1. Turn the ignition switch ON.
2. Select “FRONT WIPER” in “Active Test” of “IPDM E/R”.
3. While performing the active test, check voltage between IPDM E/R harness connector and ground.
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> Replace IPDM E/R. Refer to
PCS-40, "Removal and Installation"
3.
CHECK FRONT WIPER MOTOR (LO) OPEN CIRCUIT
1. Turn the ignition switch OFF.
2. Disconnect IPDM E/R and front wiper motor.
3. Check continuity between IPDM E/R harness connector and front wiper motor harness connector.
Is the inspection result normal?
YES
>> Replace front wiper motor. Refer to
WW-69, "Removal and Installation"
LO
: Front wiper (LO) operation
OFF
: Front wiper OFF
Component
Capacity
Fuse No.
Location
Front wiper motor
30A
43
IPDM E/R
IPDM E/R
Ground
FRONT WIPER
Voltage
(Approx.)
Connector
Terminal
E121
48
LO
Battery voltage
OFF
0V
IPDM E/R
Front wiper motor
Continuity
Connector
Terminal
Connector
Terminal
E121
48
E20
3
Yes
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст