Nissan Rogue. Manual — part 1258
FRONT WIPER MOTOR LO CIRCUIT
WW-35
< DTC/CIRCUIT DIAGNOSIS >
C
D
E
F
G
H
I
J
K
M
A
B
WW
N
O
P
NO
>> Repair or replace harness.
WW-36
< DTC/CIRCUIT DIAGNOSIS >
FRONT WIPER MOTOR HI CIRCUIT
FRONT WIPER MOTOR HI CIRCUIT
Component Function Check
INFOID:0000000011280394
1.
CHECK FRONT WIPER HI OPERATION
CONSULT ACTIVE TEST
1. Select “FRONT WIPER” in “Active Test” of “IPDM E/R”.
2. Check front wiper operation.
Is the inspection result normal?
YES
>> Front wiper motor HI circuit is normal.
NO
>> Refer to
.
Diagnosis Procedure
INFOID:0000000011280395
Regarding Wiring Diagram information, refer to
.
1.
CHECK FRONT WIPER MOTOR FUSE
1. Turn the ignition switch OFF.
2. Check that the following fuse is not blown:
Is the fuse blown?
YES
>> Replace the blown fuse after repairing the affected circuit.
NO
>> GO TO 2.
2.
CHECK FRONT WIPER MOTOR (HI) OUTPUT VOLTAGE
1. Turn the ignition switch ON.
2. Select “FRONT WIPER” in “Active Test” of “IPDM E/R”.
3. While performing the active test, check voltage between IPDM E/R harness connector and ground.
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> Replace IPDM E/R. Refer to
PCS-40, "Removal and Installation"
3.
CHECK FRONT WIPER MOTOR (HI) OPEN CIRCUIT
1. Turn the ignition switch OFF.
2. Disconnect IPDM E/R and front wiper motor.
3. Check continuity between IPDM E/R harness connector and front wiper motor harness connector.
Is the inspection result normal?
YES
>> Replace front wiper motor. Refer to
WW-69, "Removal and Installation"
HI
: Front wiper (HI) operation
OFF
: Front wiper OFF
Component
Capacity
Fuse No.
Location
Front wiper motor
30A
43
IPDM E/R
IPDM E/R
Ground
FRONT WIPER
Voltage
(Approx.)
Connector
Terminal
E121
45
HI
Battery voltage
OFF
0V
IPDM E/R
Front wiper motor
Continuity
Connector
Terminal
Connector
Terminal
E121
45
E20
5
Yes
FRONT WIPER MOTOR HI CIRCUIT
WW-37
< DTC/CIRCUIT DIAGNOSIS >
C
D
E
F
G
H
I
J
K
M
A
B
WW
N
O
P
NO
>> Repair or replace harness.
WW-38
< DTC/CIRCUIT DIAGNOSIS >
FRONT WIPER AUTO STOP SIGNAL CIRCUIT
FRONT WIPER AUTO STOP SIGNAL CIRCUIT
Component Function Check
INFOID:0000000011280396
1.
CHECK FRONT WIPER (AUTO STOP) SIGNAL
1. Select “FR WIPER STOP” in “Data Monitor” of “BCM (WIPER)”.
2. Operate the front wiper.
3. Check that FR WIPER STOP changes from ON to OFF according to the wiper position.
Is the inspection result normal?
YES
>> Front wiper auto stop signal circuit is normal.
NO
>> Refer to
.
Diagnosis Procedure
INFOID:0000000011280397
Regarding Wiring Diagram information, refer to
.
1.
CHECK FRONT WIPER MOTOR (AUTO STOP) OUTPUT VOLTAGE
1. Turn the ignition switch ON.
2. Check voltage between IPDM E/R harness connector and ground.
Is the inspection result normal?
YES
>> Check for intermittent failure.
NO
>> GO TO 2.
2.
CHECK FRONT WIPER MOTOR (AUTO STOP) SHORT CIRCUIT
1. Turn the ignition switch OFF.
2. Disconnect IPDM E/R and front wiper motor.
3. Check continuity between IPDM E/R harness connector and ground.
Is the inspection result normal?
YES
>> Repair or replace harness.
NO
>> GO TO 3.
3.
CHECK FRONT WIPER MOTOR (AUTO STOP) CIRCUIT CONTINUITY
Check continuity between IPDM E/R harness connector and front wiper motor harness connector.
Is the inspection result normal?
Data monitor
Condition
Status
FR WIPER STOP
Front wiper motor
Stop position
ON
Except stop position
OFF
IPDM E/R
Ground
FRONT WIPER
Voltage
(Approx.)
Connector
Terminal
E120
33
Except stop position
Battery voltage
Stop position
0 V
IPDM E/R
Ground
Continuity
Connector
Terminal
E120
33
No
IPDM E/R
Front wiper motor
Continuity
Connector
Terminal
Connector
Terminal
E120
33
E20
4
Yes
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст