Nissan Rogue. Manual — part 899
RECOMMENDED FLUIDS AND LUBRICANTS
MA-11
< PERIODIC MAINTENANCE >
C
D
E
F
G
H
I
J
K
L
M
B
MA
N
O
A
RECOMMENDED FLUIDS AND LUBRICANTS
Fluids and Lubricants
INFOID:0000000011277763
The following are approximate capacities. The actual capacities may be slightly different.When refilling, follow
the procedures described elsewhere in this manual.
Engine Oil Recommendation
INFOID:0000000011277764
NISSAN recommends the use of an resource conserving oil in order to improve fuel economy.
Capacity (Approximate)
Recommended Fluids/Lubricants
Liter
US measure
Imp measure
Fuel
55
14-1/2 gal
12-1/8 gal
Unleaded gasoline with an octane rating of at
least 87 AKI (RON 91)
Engine oil
Drain and refill
With oil filter
change
4.6
4-7/8 qt
4 qt
Genuine NISSAN engine oil
(For additional information, see “Engine Oil
Recommendation”.)
Engine oil with API Certification Mark
(For additional information, see “Engine Oil
Recommendation”.)
Viscosity SAE 0W-20
(As an alternative to this recommended oil,
SAE 5W-30 conventional petroleum based oil
may be used and meet all specifications and
requirements necessary to maintain the New
Vehicle Limited Warranty.)
Without oil fil-
ter change
4.3
4-1/2 qt
3-3/4 qt
Dry engine (Overhaul)
5.3
5-5/8 qt
4-5/8 qt
Cooling system
With reservoir
tank
8.1
8-5/8 qt
7-1/8 qt
Pre-diluted Genuine NISSAN Long Life Anti-
freeze/Coolant (blue) or equivalent
Reservoir
tank
0.61
5/8 qt
1/2 qt
CVT fluid
7.9
8-3/8 qt
7 qt
Genuine NISSAN CVT Fluid NS-3
(Use only Genuine NISSAN CVT Fluid NS-3.
Using transmission fluid other than Genuine
NISSAN CVT Fluid NS-3 will damage the CVT,
which is not covered by the NISSAN new ve-
hicle limited warranty.)
Differential gear oil
0.55
1-1/8 pt
1 pt
Genuine NISSAN Differential Oil Hypoid Su-
per GL-5 80W-90 or API GL-5, Viscosity SAE
80W-90
[For hot climates, viscosity SAE 90 is suitable
for ambient temperatures above 0
°C (32°F).]
Transfer oil
0.31
5/8 pt
1/2 qt
Genuine NISSAN Differential Oil Hypoid Su-
per GL-5 80W-90 or API GL-5, Viscosity SAE
80W-90
Brake fluid
—
—
—
Genuine NISSAN Super Heavy Duty Brake
Fluid or equivalent DOT 3 (US FMVSS No.
116)
(Available in mainland U.S.A. through a NIS-
SAN dealer.)
Multi-purpose grease
—
—
—
NLGI No. 2 (Lithium soap base)
Windshield washer fluid
5.2
5-1/2 qt
4-5/8 qt
Genuine NISSAN Windshield Washer Con-
centrate Cleaner & Antifreeze or equivalent
Air conditioning system refrigerant
0.50 kg
1.10 lb
1.10 lb
HFC-134a (R-134a)
(For further information, see “Air conditioning
specification label” found under the hood.)
Air conditioning system oil
110 m
3.7 fl oz
3.9 fl oz
A/C System Oil Type ND-OIL8
(For further information, see “Air conditioning
specification label” found under the hood.)
MA-12
< PERIODIC MAINTENANCE >
RECOMMENDED FLUIDS AND LUBRICANTS
Select only engine oils that meet the American Petroleum Institute (API) certification and International Lubri-
cant Standardization and Approval Committee (ILSAC) certification and SAE viscosity standard. These oils
have the API certification mark on the front of the container. Oils which do not have the specified quality label
should not be used as they could cause engine damage.
Anti-Freeze Coolant Mixture Ratio
INFOID:0000000011277765
The engine cooling system is filled at the factory with a pre-diluted mixture of 50% Genuine NISSAN Long Life
Antifreeze/Coolant (blue) and 50% water to provide year-round anti-freeze and coolant protection. The anti-
freeze solution contains rust and corrosion inhibitors. Additional engine cooling system additives are not nec-
essary.
WARNING:
• Do not remove the radiator cap when the engine is hot. Serious burns could occur from high pres-
sure engine coolant escaping from the radiator. Wrap a thick cloth around the cap. Slowly turn it a
quarter turn to allow built-up pressure to escape. Carefully remove the cap by turning it all the way.
• The radiator is equipped with a pressure type radiator cap. To prevent engine damage, use only a
genuine NISSAN radiator cap.
CAUTION:
• When adding or replacing coolant, be sure to use only Genuine NISSAN Long Life Antifreeze/Cool-
ant (blue) or equivalent. Genuine NISSAN Long Life Antifreeze/Coolant (blue) is pre-diluted to pro-
vide antifreeze protection to -34
°F (-37°C). If additional freeze protection is needed due to weather
where you operate your vehicle, add Genuine NISSAN Long Life Antifreeze/Coolant (blue) concen-
trate following the directions on the container. If an equivalent coolant other than Genuine NISSAN
Long Life Antifreeze/Coolant (blue) is used, follow the coolant manufactur's instructions to maintain
minimum antifreeze protection to -34
°F (-37°C). The use of other types of coolant solutions other
than Genuine NISSAN Long Life Antifreeze/Coolant (blue) or equivalent may damage the engine
cooling system.
• Mixing any other type of coolant other than Genuine NISSAN Long Life Antifreeze/Coolant (blue),
including Genuine NISSAN Long Life Antifreeze/Coolant (green), or the use of non-distilled water will
reduce the life expectancy of the factory-fill coolant.
1. API certification mark
2. API service symbol
ALPIA0008ZZ
ENGINE MAINTENANCE
MA-13
< PERIODIC MAINTENANCE >
C
D
E
F
G
H
I
J
K
L
M
B
MA
N
O
A
ENGINE MAINTENANCE
DRIVE BELTS
DRIVE BELTS : Exploded View
INFOID:0000000011378293
DRIVE BELTS : Checking
INFOID:0000000011378294
WARNING:
Inspect the drive belt only when the engine is stopped.
1. Visually check entire drive belt for wear, damage or cracks.
2. Check that the drive belt auto-tensioner indicator is within the possible use range.
NOTE:
• When new drive belt is installed, the drive belt auto-tensioner indicator should be within the new drive
belt range.
• Check the drive belt auto-tensioner indicator when the engine is cold.
3. If the drive belt auto-tensioner indicator is out of the possible use range or belt is damaged, replace drive
belt.
DRIVE BELTS : Tension Adjustment
INFOID:0000000011378295
Belt tension is not manually adjustable. It is automatically adjusted by the drive belt auto-tensioner.
DRIVE BELTS : Removal and Installation
INFOID:0000000011378296
REMOVAL
1. Remove wheel and tire (RH) using a power tool.
2. Remove engine under cover. Refer to
EXT-37, "ENGINE UNDER COVER : Removal and Installation"
3. Remove fender protector side cover. Refer to
EXT-28, "FENDER PROTECTOR : Exploded View"
1.
Generator pulley
2.
Water pump pulley
3.
Drive belt auto-tensioner
4.
Crankshaft pulley
5.
A/C compressor pulley
6.
Drive belt retainer boss
A.
View A
B.
New drive belt range
C.
Possible use range
D.
Indicator (notch)
AWBIA1893ZZ
MA-14
< PERIODIC MAINTENANCE >
ENGINE MAINTENANCE
4. Securely hold the hexagonal part (A) of drive belt auto-tensioner
(1) using suitable tool, and move in the direction of arrow (loos-
ening direction of tensioner).
5. Insert a rod approximately 6 mm (0.24 in) in diameter through
the rear of the drive belt auto-tensioner into retaining boss (B) to
lock drive belt auto-tensioner pulley.
WARNING:
Avoid placing hand in a location where pinching may occur
if the holding tool accidentally comes off.
NOTE:
Leave drive belt auto-tensioner pulley arm locked until drive belt
is installed again.
6. Loosen drive belt from drive belt auto-tensioner and then remove it from the other pulleys.
7. Installation of remaining components is in the reverse order of removal.
INSTALLATION
Installation is in the reverse order of removal.
1. Install the drive belt onto all of the pulleys except for the drive belt auto-tensioner. Then install the drive
belt onto drive belt auto-tensioner last.
CAUTION:
• Confirm belts are completely set on the pulleys.
• Check for engine oil and engine coolant. Be sure they are not adhered to the drive belt and each
pulley groove.
2. Release the drive belt auto-tensioner and apply tension to drive belt.
WARNING:
Avoid placing hand in a location where pinching may occur if the holding tool accidentally comes
off.
3. Turn crankshaft pulley clockwise several times to equalize tension between each pulley.
4. Confirm the indicator is within the possible use range. Refer to
MA-13, "DRIVE BELTS : Checking"
5. Install wheel and tire (RH). Refer to
.
DRIVE BELTS : Removal and Installation of Drive Belt Auto-tensioner
INFOID:0000000011378297
REMOVAL
CAUTION:
The complete drive belt auto-tensioner must be replaced as a unit, including the pulley.
ALBIA0879GB
1.
Drive belt auto-tensioner
AWBIA1381ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст