Nissan Rogue. Manual — part 900
ENGINE MAINTENANCE
MA-15
< PERIODIC MAINTENANCE >
C
D
E
F
G
H
I
J
K
L
M
B
MA
N
O
A
1. Remove the drive belt. Refer to
MA-13, "DRIVE BELTS : Removal and Installation"
.
2. Remove the drive belt auto-tensioner.
INSTALLATION
Installation is in the reverse order of removal.
CAUTION:
• Install the drive belt auto-tensioner carefully so not to damage the water pump pulley.
• If there is damage greater than peeled paint, replace the drive belt auto-tensioner.
AIR CLEANER FILTER
AIR CLEANER FILTER : Exploded View
INFOID:0000000011378298
AIR CLEANER FILTER : Removal and Installation
INFOID:0000000011378299
CHANGING THE AIR CLEANER FILTER
1. Remove air duct assembly from air cleaner case (upper).
2. Open the air cleaner case.
3. Remove the air cleaner filter.
4. Install a new air cleaner filter.
5. Close the air cleaner case.
6. Secure the air cleaner case clips.
INSPECTION AFTER REMOVAL
Examine the air cleaner filter for stains, clogging, or damage.
• Remove dirt and foreign objects (such as dead leaves) on air cleaner filter surface and inside cleaner case.
• If clogging or damage is observed, replace the air cleaner filter.
CAUTION:
Do not clean the viscous paper type air cleaner filter by blowing as there is a risk of deterioration of its
performance.
MAINTENANCE INTERVAL
MA-7, "Introduction of Periodic Maintenance"
1.
Mass air flow sensor
2.
Air cleaner filter
3.
Air cleaner case (lower)
4.
Air duct assembly
5.
Grommet
6.
Resonator bracket (front)
7.
Resonator bracket (rear)
8.
Resonator
9.
Air duct
10.
Mounting clip
11.
Air duct assembly
12.
Air duct assembly
13.
Air cleaner bracket
14.
Grommet
15.
Air cleaner case (upper)
A.
To Electric throttle control actuator
AWBIA2261ZZ
MA-16
< PERIODIC MAINTENANCE >
ENGINE MAINTENANCE
SPARK PLUG
SPARK PLUG : Exploded View
INFOID:0000000011378300
SPARK PLUG : Removal and Installation
INFOID:0000000011378301
REMOVAL
1. Remove air duct assembly.
2. Remove ignition coil. Refer to
.
3. Remove spark plug using Tool.
INSPECTION AFTER REMOVAL
Visually check the electrode for dirt and wear and the insulator for burning.
1. Ignition coil
2. Spark plug
3. Rocker cover
AWBIA1302GB
Tool number
: — (J-48891)
ALBIA0672GB
(A)
: Iridium alloy
AWBIA1745ZZ
ENGINE MAINTENANCE
MA-17
< PERIODIC MAINTENANCE >
C
D
E
F
G
H
I
J
K
L
M
B
MA
N
O
A
• Do not use a wire brush for cleaning the spark plugs. Replace as
necessary.
• If plug is covered with carbon, a spark plug cleaner may be used.
• Checking and adjusting plug gap is not required between change
intervals. If the gap is out of specification, replace the spark plug.
CAUTION:
Do not drop or shock plug.
INSTALLATION
Installation is in the reverse order of removal.
*: Always check with the Parts Department for the latest parts information.
ENGINE OIL
ENGINE OIL : Inspection
INFOID:0000000011277775
ENGINE OIL LEVEL
NOTE:
Before starting engine, put vehicle horizontally and check the engine oil level. If engine is already started, stop
it and allow 5 minutes before checking.
1. Pull out oil level gauge and wipe it clean.
2. Insert oil level gauge and check the engine oil level is within the
range (A) as shown.
3. If it is out of range, adjust it.
SMA773C
Cleaner air pressure : less than 588 kPa (6 kg/cm
2
, 85 psi)
Cleaning time
: less than 20 seconds
SMA806CA
Standard type*
DENSO
FXE20HE11C
Gap (nominal)
1.1 mm (0.043 in)
PBIC3309J
MA-18
< PERIODIC MAINTENANCE >
ENGINE MAINTENANCE
ENGINE OIL APPEARANCE
• Check engine oil for white milky appearance or excessive contamination.
• If engine oil becomes turbid and white, it is highly probable that it is contaminated with engine coolant.
Repair or replace damaged parts.
ENGINE OIL LEAKS
Check for engine oil leaks around the following areas:
• Oil temperature sensor
• Oil level sensor
• Oil level gauge assembly O-ring.
• Crankshaft position sensor
• Camshaft position sensors
• Oil cooler
• Oil pan (upper and lower)
• Oil pan drain plug
• Oil pressure switch
• Oil filter
• Intake valve timing intermediate lock control solenoid valve
• Intake valve timing control solenoid valve
• Exhaust valve timing control solenoid valve
• Front cover
• Mating surface between cylinder head and camshaft bracket
• Mating surface between cylinder block and cylinder head
• Mating surface between cylinder head and rocker cover
• Crankshaft oil seals (front and rear)
OIL PRESSURE CHECK
WARNING:
• Be careful not to get burn yourself, as engine oil may be hot.
• When checking engine oil pressure, shift selector should be in "P" position. Be sure to apply parking
brake.
1. Check the engine oil level.
2. Remove fender protector side cover (RH). Refer to
EXT-28, "FENDER PROTECTOR : Exploded View"
.
3. Disconnect harness connector at oil pressure switch and remove oil pressure switch using suitable tool.
CAUTION:
Do not drop or shock oil pressure switch.
4. Install suitable tools (A/B).
5. Start the engine and warm it up to normal operating temperature.
6. Check the engine oil pressure with engine running under no-load.
NOTE:
• When engine oil temperature is low, engine oil pressure becomes high.
• If difference is extreme, check oil passage and oil pump for engine oil leaks.
7. After the inspections, install oil pressure switch as follows:
a. Remove old liquid gasket adhering to oil pressure switch and engine.
b. Apply liquid gasket and tighten oil pressure switch to the specification.
JPBIA0074ZZ
Engine oil pressure
: Refer to
.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст