Nissan Rogue. Manual — part 929
MWI
FUEL LEVEL SENSOR SIGNAL CIRCUIT
MWI-63
< DTC/CIRCUIT DIAGNOSIS >
C
D
E
F
G
H
I
J
K
L
M
B
A
O
P
FUEL LEVEL SENSOR SIGNAL CIRCUIT
Component Function Check
INFOID:0000000011279813
1.
COMBINATION METER INPUT SIGNAL
1. Select “METER/M&A” using CONSULT.
2. Select “FUEL METER” in “Data Monitor”.
3. Check the “FUEL METER” value and compare with the fuel gauge of the combination meter. Fuel gauge
and Data Monitor indications should be close.
Does the data monitor value approximately match the fuel gauge indication?
YES
>> Inspection End.
NO
>> Replace combination meter. Refer to
MWI-84, "Removal and Installation"
Diagnosis Procedure
INFOID:0000000011279814
1.
CHECK FUEL LEVEL SENSOR UNIT AND FUEL PUMP (FUEL LEVEL SENSOR) CIRCUIT
1. Turn ignition switch OFF.
2. Disconnect combination meter connector and fuel level sensor unit and fuel pump (fuel level sensor) con-
nector.
3. Check continuity between combination meter harness connector and fuel level sensor unit and fuel pump
(fuel level sensor) harness connector.
4. Check continuity between combination meter harness connector and ground.
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> Repair harness or connector.
2.
CHECK FUEL LEVEL SENSOR UNIT AND FUEL PUMP (FUEL LEVEL SENSOR) GROUND CIRCUIT
Check continuity between fuel level sensor unit and fuel pump (fuel level sensor) harness connector and com-
bination meter harness connector.
Is the inspection result normal?
Combination meter
Monitor item
Fuel gauge
FUEL METER [L]
(Approx.)
Full
55
3/4
41.2
1/2
27.5
1/4
13.7
Empty
0.0
Combination meter
Fuel level sensor unit and fuel pump (fuel level sensor)
Continuity
Connector
Terminal
Connector
Terminal
M77
51
B103
5
Yes
Combination meter
Ground
Continuity
Connector
Terminal
M77
51
No
Fuel level sensor unit and fuel pump (fuel level sensor)
Combination meter
Continuity
Connector
Terminal
Connector
Terminal
B103
2
M77
44
Yes
MWI-64
< DTC/CIRCUIT DIAGNOSIS >
FUEL LEVEL SENSOR SIGNAL CIRCUIT
YES
>> Replace combination meter. Refer to
MWI-84, "Removal and Installation"
NO
>> Repair harness or connector.
Component Inspection
INFOID:0000000011279815
1.
CHECK FUEL LEVEL SENSOR UNIT AND FUEL PUMP (FUEL LEVEL SENSOR)
1. Remove the fuel level sensor unit and fuel pump (fuel level sensor). Refer to
2. Check the resistance between fuel level sensor unit and fuel
pump (fuel level sensor).
*: When float rod is contact with stopper.
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> Replace fuel level sensor unit and fuel pump (fuel level sensor). Refer to
2.
CHECK FUEL LEVEL SENSOR UNIT (SUB)
1. Remove the fuel level sensor unit (sub). Refer to
FL-5, "Removal and Installation"
.
2. Check the resistance between fuel level sensor unit (sub).
*: When float rod is contact with stopper.
Is the inspection result normal?
YES
>> Inspection End.
NO
>> Replace fuel level sensor unit (sub). Refer to
.
Terminals
Condition
Resistance (
Ω)
(Approx.)
Height [mm (in)]
Fuel level sensor unit and
fuel pump (fuel level sensor)
2
8
Full
*
(A)
45
171.4 (6.7)
Empty
*
(B)
141
20.5 (0.8)
5
7
—
0
—
AWNIA3403ZZ
Terminals
Condition
Resistance (
Ω)
(Approx.)
Height [mm (in)]
Fuel level sensor unit (sub)
7
8
Full
*
(A)
6.0
194.1 (7.6)
Empty
*
(B)
141
18 (0.7)
AWNIA3404ZZ
MWI
PARKING BRAKE SWITCH SIGNAL CIRCUIT
MWI-65
< DTC/CIRCUIT DIAGNOSIS >
C
D
E
F
G
H
I
J
K
L
M
B
A
O
P
PARKING BRAKE SWITCH SIGNAL CIRCUIT
Description
INFOID:0000000011279816
Transmits the parking brake switch signal to the combination meter.
Component Function Check
INFOID:0000000011279817
1.
COMBINATION METER INPUT SIGNAL
1. Select “METER/M&A” using CONSULT.
2. Select “PKB SW” in “Data Monitor”.
3. Check the “PKB SW” status according to the following conditions:
Is the inspection result normal?
YES
>> Inspection End.
NO
>> Refer to
Diagnosis Procedure
INFOID:0000000011279818
Regarding Wiring Diagram information, refer to
.
1.
CHECK PARKING BRAKE SWITCH CIRCUIT
1. Disconnect combination meter harness connector M76 and parking brake switch harness connector E52.
2. Check continuity between combination meter harness connector M76 terminal 26 and parking brake
switch harness connector E52 terminal 1.
3. Check continuity between combination meter harness connector M76 terminal 26 and ground.
Is the inspection result normal?
YES
>> Inspection End.
NO
>> Repair or replace harness or connector.
Component Inspection
INFOID:0000000011279819
1.
CHECK PARKING BRAKE SWITCH
Check continuity between parking brake switch terminal 1 and switch case ground.
Is the inspection result normal?
YES
>> Inspection End.
Monitor item
Condition
Status
PKB SW
Parking brake applied
On
Parking brake released
Off
Combination meter
Parking brake switch
Continuity
Connector
Terminal
Connector
Terminal
M76
26
E52
1
Yes
Combination meter
Ground
Continuity
Connector
Terminal
M76
26
No
Component
Terminal
Condition
Continuity
Parking brake switch
1
Parking brake applied
Yes
Parking brake released
No
MWI-66
< DTC/CIRCUIT DIAGNOSIS >
PARKING BRAKE SWITCH SIGNAL CIRCUIT
NO
>> Replace parking brake switch. Refer to
.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст