Nissan Rogue. Manual — part 906
CHASSIS MAINTENANCE
MA-39
< PERIODIC MAINTENANCE >
C
D
E
F
G
H
I
J
K
L
M
B
MA
N
O
A
Check ball joint, dust cover and other component parts for looseness, wear, damage and grease leakage.
AXLE AND SUSPENSION PARTS
AXLE AND SUSPENSION PARTS : Inspection
INFOID:0000000011277809
Check front and rear axle and suspension parts for excessive play,
cracks, wear or other damage.
• Shake each wheel to check for excessive play.
• Check wheel bearings for smooth operation.
• Check axle and suspension nuts and bolts for looseness.
• Check strut (shock absorber) for oil leakage or other damage.
• Check suspension ball joint for grease leakage and ball joint dust
cover for cracks or other damage.
DRIVE SHAFT
DRIVE SHAFT : Inspection
INFOID:0000000011277810
• Check boot and drive shaft for cracks, wear, damage and grease
leakage.
LOCKS, HINGES AND HOOD LATCH
LOCKS, HINGES AND HOOD LATCH : Lubricating
INFOID:0000000011277811
WITH INTELLIGENT KEY SYSTEM
For hood and hood lock illustration.
• Hood lock control: Refer to
For front door and front door lock illustration.
• Front door: Refer to
• Front door lock: Refer to
• Rear door: Refer to
.
• Rear door lock: Refer to
.
For back door and back door lock illustration.
SMA525A
JPPIA0011ZZ
SFA108A
MA-40
< PERIODIC MAINTENANCE >
CHASSIS MAINTENANCE
• Back door: Refer to
• Back door lock: Refer to
.
WITHOUT INTELLIGENT KEY SYSTEM
For hood and hood lock illustration.
• Hood lock control: Refer to
For front door and front door lock illustration.
• Front door lock: Refer to
.
• Rear door: Refer to
.
• Rear door lock: Refer to
.
For back door and back door lock illustration.
• Back door: Refer to
• Back door lock: Refer to
.
SEAT BELT, BUCKLES, RETRACTORS, ANCHORS AND ADJUSTERS
SEAT BELT, BUCKLES, RETRACTORS, ANCHORS AND ADJUSTERS : Inspection
INFOID:0000000011277812
For front seat belt illustration. Refer to
For rear seat belt illustration. Refer to
CAUTION:
• After any collision, inspect all seat belt assemblies, including retractors and other attached hard-
wares (I.e. anchor bolt, guide rail set). Nissan recommends to replace all seat belt assemblies in use
during a collision, unless not damaged and properly operating after minor collision.
Also inspect seat belt assemblies not in use during a collision, and replace if damaged or improperly
operating.
Seat belt pre-tensioner should be replaced even if the seat belts are not in use during a frontal colli-
sion where the driver and passenger air bags are deployed.
• If any component of seat belt assembly is questionable, do not repair.
Replace as seat belt assembly.
• If webbing is cut, frayed, or damaged, replace belt assembly.
• Never oil tongue and buckle.
• Use a genuine NISSAN seat belt assembly.
For details, refer to
in SB section.
• Check anchors for loose mounting
• Check belts for damage
• Check retractor for smooth operation
• Check function of buckles and tongues when buckled and released
MIR-1
DRIVER CONTROLS
C
D
E
F
G
H
I
J
K
M
SECTION
MIR
A
B
MIR
N
O
P
CONTENTS
MIRRORS
PRECAUTION . . . . . . . . . . . ...
PRECAUTIONS . . . . . . . . . . . . ...
Precaution for Work . . . . . . . . . . . . ..
PREPARATION . . . . . . . . . . .
PREPARATION . . . . . . . . . . . . ...
Special Service Tool . . . . . . . . . . . .....
Commercial Service Tools . . . . . . . . . ...
WIRING DIAGRAM . . . . . . . . . ...
INSIDE MIRROR . . . . . . . . . . . . .
Wiring Diagram - With Homelink Universal Trans-
ceiver . . . . . . . . . . . . . . . . . .....
Wiring Diagram - Without Homelink Universal
Transceiver . . . . . . . . . . . . . . . ...
DOOR MIRROR . . . . . . . . . . . . ..
Wiring Diagram . . . . . . . . . . . . . ...
DTC/CIRCUIT DIAGNOSIS . . . . . . .
DOOR MIRROR REMOTE CONTROL
SWITCH . . . . . . . . . . . . . . . ..
Component Inspection . . . . . . . . . . .
SYMPTOM DIAGNOSIS . . . . . . . ..
SQUEAK AND RATTLE TROUBLE DIAG-
NOSES . . . . . . . . . . . . . . . ..
Work Flow . . . . . . . . . . . . . . . .
Generic Squeak and Rattle Troubleshooting . . ...
Diagnostic Worksheet . . . . . . . . . . . ..
REMOVAL AND INSTALLATION . . . ...
INSIDE MIRROR . . . . . . . . . . . ...
Exploded View . . . . . . . . . . . . . . .
Removal and Installation . . . . . . . . . . .
DOOR MIRROR . . . . . . . . . . . .
Exploded View . . . . . . . . . . . . . . .
Removal and Installation . . . . . . . . . . .
DOOR MIRROR GLASS . . . . . . . . ...
Removal and Installation . . . . . . . . . . .
DOOR MIRROR ACTUATOR . . . . . . ...
Removal and Installation . . . . . . . . . . .
DOOR MIRROR REAR FINISHER . . . . ...
Removal and Installation . . . . . . . . . . .
SIDE CAMERA FINISHER . . . . . . . .
Removal and Installation . . . . . . . . . . .
DOOR MIRROR REMOTE CONTROL
SWITCH . . . . . . . . . . . . . . . .
MIR-2
< PRECAUTION >
PRECAUTIONS
PRECAUTION
PRECAUTIONS
Precaution for Supplemental Restraint System (SRS) "AIR BAG" and "SEAT BELT
PRE-TENSIONER"
INFOID:0000000011280681
The Supplemental Restraint System such as “AIR BAG” and “SEAT BELT PRE-TENSIONER”, used along
with a front seat belt, helps to reduce the risk or severity of injury to the driver and front passenger for certain
types of collision. Information necessary to service the system safely is included in the SR and SB section of
this Service Manual.
WARNING:
• To avoid rendering the SRS inoperative, which could increase the risk of personal injury or death in
the event of a collision which would result in air bag inflation, all maintenance must be performed by
an authorized NISSAN/INFINITI dealer.
• Improper maintenance, including incorrect removal and installation of the SRS, can lead to personal
injury caused by unintentional activation of the system. For removal of Spiral Cable and Air Bag
Module, see the SR section.
• Do not use electrical test equipment on any circuit related to the SRS unless instructed to in this
Service Manual. SRS wiring harnesses can be identified by yellow and/or orange harnesses or har-
ness connectors.
PRECAUTIONS WHEN USING POWER TOOLS (AIR OR ELECTRIC) AND HAMMERS
WARNING:
• When working near the Airbag Diagnosis Sensor Unit or other Airbag System sensors with the Igni-
tion ON or engine running, DO NOT use air or electric power tools or strike near the sensor(s) with a
hammer. Heavy vibration could activate the sensor(s) and deploy the air bag(s), possibly causing
serious injury.
• When using air or electric power tools or hammers, always switch the Ignition OFF, disconnect the
battery and wait at least three minutes before performing any service.
Precaution for Work
INFOID:0000000011280682
• When removing or disassembling each component, be careful not to damage or deform it. If a component
may be subject to interference, be sure to protect it with a shop cloth.
• When removing (disengaging) components with a screwdriver or similar tool, be sure to wrap the component
with a shop cloth or vinyl tape to protect it.
• Protect the removed parts with a shop cloth and prevent them from being dropped.
• Replace a deformed or damaged clip.
• If a part is specified as a non-reusable part, always replace it with a new one.
• Be sure to tighten bolts and nuts securely to the specified torque.
• After installation is complete, be sure to check that each part works properly.
• Follow the steps below to clean components:
- Water soluble dirt:
• Dip a soft cloth into lukewarm water, wring the water out of the cloth and wipe the dirty area.
• Then rub with a soft, dry cloth.
- Oily dirt:
• Dip a soft cloth into lukewarm water with mild detergent (concentration: within 2 to 3%) and wipe the dirty
area.
• Then dip a cloth into fresh water, wring the water out of the cloth and wipe the detergent off.
• Then rub with a soft, dry cloth.
- Do not use organic solvent such as thinner, benzene, alcohol or gasoline.
- For genuine leather seats, use a genuine leather seat cleaner.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст