Nissan Rogue. Manual — part 905
CHASSIS MAINTENANCE
MA-35
< PERIODIC MAINTENANCE >
C
D
E
F
G
H
I
J
K
L
M
B
MA
N
O
A
• Perform the ID registration after tire rotation. Refer to
BRAKE LINES AND CABLES
BRAKE LINES AND CABLES : Inspection
INFOID:0000000011277801
• Check brake fluid lines and parking brake cables for improper
attachment, leaks, chafing, abrasions, deterioration, etc.
BRAKE FLUID
BRAKE FLUID : Inspection
INFOID:0000000011277802
BRAKE FLUID LEVEL
• Make sure that the brake fluid level in the reservoir tank is between
the MAX and MIN lines.
• Visually check around the reservoir tank for brake fluid leakage.
• If the brake fluid level is excessively low, check the brake system
for leakage.
• If brake warning lamp remains illuminated after parking brake
pedal is released, check the brake system for brake fluid leakage.
BRAKE LINE
1. Check brake line (tubes and hoses) for cracks, deterioration or other damage. Replace any damaged
parts.
2. Check for brake fluid leakage by fully depressing brake pedal
while engine is running.
CAUTION:
If brake fluid leakage occurs around joints, retighten or
replace damaged parts as necessary.
BRAKE FLUID : Drain and Refill
INFOID:0000000011277803
CAUTION:
• Do not spill or splash brake fluid on painted surfaces. Brake fluid may damage paint. If brake fluid is
splashed on painted areas, wash it away with water immediately.
• Prior to repair, turn the ignition switch OFF, disconnect the ABS actuator and electric unit (control
unit) connector or negative battery terminal. Refer to
PG-78, "Removal and Installation (Battery)"
.
Wheel nut tightening torque
SBR389C
JPFIA0007ZZ
SBR389C
MA-36
< PERIODIC MAINTENANCE >
CHASSIS MAINTENANCE
• Refill brake system with new brake fluid. Refer to
MA-11, "Fluids and Lubricants"
• Do not reuse drained brake fluid.
DRAINING
1. Turn ignition switch OFF and disconnect ABS actuator and electric unit (control unit) connector or nega-
tive battery terminal. Refer to
PG-78, "Removal and Installation (Battery)"
.
2. Connect a vinyl tube to bleeder valve.
3. Depress brake pedal, loosen bleeder valve, and gradually
remove brake fluid.
CAUTION:
Do not allow master cylinder reservoir tank to empty as this
may cause damage to master cylinder internal components.
REFILLING
1. Make sure no foreign material is in the reservoir tank, and refill
with new brake fluid.
CAUTION:
Do not reuse drained brake fluid.
2. Refill the brake system as follows:
• Depress the brake pedal.
• Loosen bleeder valve.
• Slowly depress brake pedal to 2/3 of the brake pedal full
stroke.
• Tighten bleeder valve.
• Release brake pedal.
Repeat this operation at intervals of two or three seconds until
all old brake fluid is discharged. Add new brake fluid frequently.
CAUTION:
Do not allow master cylinder reservoir tank to empty as this may cause damage to master cylinder
internal components.
3. Bleed the air out of the brake hydraulic system. Refer to
BR-16, "Bleeding Brake System"
.
FRONT BRAKE
FRONT BRAKE : Inspection
INFOID:0000000011277804
Check brake pad wear thickness from an inspection hole (A) on cyl-
inder body. Check using a scale if necessary.
FRONT BRAKE : Inspection
INFOID:0000000011277805
APPEARANCE
Check surface of disc brake rotor for uneven wear, cracks or damage. Replace if any abnormal conditions
exist.
RUNOUT
BRA0007D
PFIA0403J
Wear thickness
: Refer to
AWFIA0891ZZ
CHASSIS MAINTENANCE
MA-37
< PERIODIC MAINTENANCE >
C
D
E
F
G
H
I
J
K
L
M
B
MA
N
O
A
1. Check the wheel bearing axial end play before the inspection. Refer to
(FWD) or
(AWD).
2. Secure the disc brake rotor to the wheel hub and bearing with
wheel nuts at two wheel nut locations.
3. Inspect the runout with a dial gauge, measured at 10 mm (0.39
in) inside the disc brake rotor edge.
4. Find the installation position with a minimum runout by shifting
the disc brake rotor-to-wheel hub and bearing installation posi-
tion by one hole at a time if the runout exceeds the limit value.
5. Refinish the disc brake rotor if the runout is outside the limit
even after performing the above operation. When refinishing,
use Tool.
CAUTION:
• Check in advance that the thickness of the disc brake rotor is wear thickness + 0.3 mm (0.012 in)
or more.
• If the thickness is less than wear thickness + 0.3 mm (0.012 in), replace the disc brake rotor.
THICKNESS
Check the thickness of the disc brake rotor using a micrometer.
Replace the disc brake rotor if the thickness is below the wear limit.
REAR BRAKE
REAR BRAKE : Inspection
INFOID:0000000011277806
INSPECTION
Check brake pad wear thickness from an inspection hole (A) on cyl-
inder body. Check using a scale if necessary.
REAR BRAKE : Inspection
INFOID:0000000011277807
Appearance
Runout
: Refer to
Tool number
: 38-PFM92
Wear thickness
: Refer to
.
SBR019B
Wear thickness
: Refer to
Thickness variation : Refer to
SBR020B
Wear thickness
: Refer to
.
ALFIA0226ZZ
MA-38
< PERIODIC MAINTENANCE >
CHASSIS MAINTENANCE
Check surface of disc brake rotor for uneven wear, cracks or damage. Replace if any abnormal conditions
exist.
Runout
1. Check the wheel bearing axial end play before the inspection. Refer to
(AWD).
2. Secure the disc brake rotor to the wheel hub and bearing with
wheel nuts at two wheel nut locations.
3. Measure the runout with a dial gauge 10 mm (0.39 in) from the
disc brake rotor edge.
4. Find the installation position with a minimum runout by shifting
the disc brake rotor-to-wheel hub and bearing installation posi-
tion by one hole at a time if the runout exceeds the limit value.
5. Refinish the disc brake rotor if the runout is outside the limit
even after performing the above operation. When refinishing, use Tool.
CAUTION:
• Check in advance that the thickness of the disc brake rotor is wear thickness + 0.3 mm (0.012 in)
or more.
• If the thickness is less than wear thickness + 0.3 mm (0.012 in), replace the disc brake rotor.
Thickness
Check the thickness of the disc brake rotor using a micrometer.
Replace the disc brake rotor if the thickness is below the minimum
thickness.
STEERING GEAR AND LINKAGE
STEERING GEAR AND LINKAGE : Inspection
INFOID:0000000011277808
STEERING GEAR
• Check gear housing and boots for looseness, damage and grease
leakage.
• Check connection with steering column for looseness.
STEERING LINKAGE
Runout
: Refer to
.
Tool number
: 38-PFM92
Wear thickness
: Refer to
.
SBR019B
Minimum thickness
: Refer to
.
Thickness variation
: Refer to
.
SBR020B
JPPIA0013GB
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст