Nissan Rogue. Manual — part 822
IP-14
< REMOVAL AND INSTALLATION >
INSTRUMENT PANEL ASSEMBLY
REMOVAL AND INSTALLATION
INSTRUMENT PANEL ASSEMBLY
Exploded View
INFOID:0000000011280352
INSTRUMENT PANEL ASSEMBLY
INSTRUMENT PANEL ASSEMBLY : Removal and Installation
INFOID:0000000011280353
CAUTION:
• Be careful not to scratch instrument panel pad and other parts.
1.
Defroster grille
2.
Center speaker grille (if equipped)
3.
Side ventilator grille (LH)
4.
Instrument side finisher (LH)
5.
Knee protector
6.
Instrument finisher A
7.
Cluster lid A
8.
Instrument finisher B (without push-
button ignition)
9.
Instrument finisher B (with push-
button ignition)
10. Upper switch carrier
11. Lower switch carrier
12. Instrument lower panel LH
13. Data link cover
14. Steering column upper cover
15. Steering column lower cover
16. Steering lock escutcheon
17. Center ventilator grille
18. Audio unit (DISPLAY AUDIO) /
AV control unit (NAVIGATION
WITHOUT BOSE) (NAVIGA-
TION WITH BOSE)
19. A/C switch assembly (AUTOMATIC
AIR CONDITONING) / front air con-
trol (MANUAL AIR CONDITIONING)
20. Cluster lid C
21. Glove box assembly
22. Glove box housing
23. Instrument finisher E
24. Instrument side finisher (RH)
25. Side ventilator grille (RH)
26. Instrument panel
Pawl
AWJIA1320ZZ
INSTRUMENT PANEL ASSEMBLY
IP-15
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
K
L
M
A
B
IP
N
O
P
• Whenever a suitable tool is used, always wrap a cloth around the end of the tool to protect compo-
nents from damage.
• Before servicing, turn ignition switch OFF, disconnect both battery terminals then wait at least three
minutes.
REMOVAL
1. Disconnect the negative and positive battery terminals, then wait at least three minutes. Refer to
"Removal and Installation (Battery)"
.
2. Remove dash side finishers (LH/RH). Refer to
INT-24, "DASH SIDE FINISHER : Removal and Installa-
3. Remove front pillar finishers (LH/RH). Refer to
INT-20, "FRONT PILLAR FINISHER : Removal and Instal-
.
4. Remove combination switch. Refer to
EXL-124, "Removal and Installation"
.
5. Remove center console assembly. Refer to
IP-19, "Removal and Installation"
.
6. Remove combination meter. Refer to
MWI-84, "Removal and Installation"
7. Remove audio unit (DISPLAY AUDIO). Refer to
AV-67, "Removal and Installation"
.
8. Remove AV control unit. Refer to
AV-200, "Removal and Installation"
(NAVIGATION WITHOUT BOSE) or
AV-369, "Removal and Installation"
(NAVIGATION WITH BOSE).
9. Remove instrument finisher A. Refer to
IP-15, "INSTRUMENT FINISHER A : Removal and Installation"
.
10. Remove instrument finisher B. Refer to
IP-16, "INSTRUMENT FINISHER B : Removal and Installation"
.
11. Remove instrument finisher E. Refer to
IP-16, "INSTRUMENT FINISHER E : Removal and Installation"
.
12. Remove glove box assembly and housing. Refer to
IP-24, "Removal and Installation"
13. Remove instrument panel assembly screws and front passenger air bag module screws.
CAUTION:
• Do not reuse the front passenger air bag module bolts.
14. Disconnect the harness connectors from the instrument panel assembly and remove.
INSTALLATION
Installation is in the reverse order of removal.
• If replacing the instrument panel, transfer all the necessary parts to the new instrument panel.
• Tighten front passenger air bag screws to specification. Refer to
CAUTION:
• Do not reuse the front passenger air bag module bolts.
• Do not damage the front passenger air bag module harnesses during installation.
• After installation is complete, check that no system malfunction is detected causing the air bag
warning lamp to illuminate.
• If a malfunction is indicated by the air bag warning lamp after repair or replacement of the malfunc-
tioning parts, perform the SRS final check. Refer to
SRC-16, "Trouble Diagnosis with CONSULT"
INSTRUMENT FINISHER A
INSTRUMENT FINISHER A : Removal and Installation
INFOID:0000000011280354
REMOVAL
1. Remove side ventilator grille (LH). Refer to
VTL-13, "SIDE VENTILATOR GRILLE : Removal and Installa-
2. Remove instrument lower panel LH. Refer to
IP-16
< REMOVAL AND INSTALLATION >
INSTRUMENT PANEL ASSEMBLY
3. Release the instrument finisher A clips and pawls using a suit-
able tool.
: Pawl
: Metal clip
4. Disconnect the harness connector from instrument finisher A and remove.
INSTALLATION
Installation is in the reverse order of removal.
INSTRUMENT FINISHER B
INSTRUMENT FINISHER B : Removal and Installation
INFOID:0000000011280355
REMOVAL
1. Remove front air control or A/C switch assembly. Refer to
HAC-182, "Removal and Installation"
(MANUAL
AIR CONDITIONING) or
HAC-102, "Removal and Installation"
(AUTOMATIC AIR CONDITIONING).
2. Release the instrument finisher B clips and pawls using a suit-
able tool.
: Pawl
: Metal clip
3. Disconnect the harness connector (if equipped) and remove instrument finisher B.
INSTALLATION
Installation is in the reverse order of removal.
INSTRUMENT FINISHER E
INSTRUMENT FINISHER E : Removal and Installation
INFOID:0000000011280356
REMOVAL
1. Remove side ventilator grille (RH). Refer to
VTL-13, "SIDE VENTILATOR GRILLE : Removal and Installa-
2. Release the clips and pawls using a suitable tool and remove
instrument finisher E.
Pawl
: Metal clip
INSTALLATION
AWJIA1309ZZ
ALJIA1400ZZ
ALJIA1399ZZ
INSTRUMENT PANEL ASSEMBLY
IP-17
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
K
L
M
A
B
IP
N
O
P
Installation is in the reverse order of removal.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст