Nissan Rogue. Manual — part 1237
WT-24
< BASIC INSPECTION >
DIAGNOSIS AND REPAIR WORK FLOW
BASIC INSPECTION
DIAGNOSIS AND REPAIR WORK FLOW
Work Flow
INFOID:0000000011280498
NOTE:
The Signal Tech II Tool [– (J-50190)] can be used to perform the following functions. Refer to the Signal Tech
II User Guide for additional information.
• Activate and display TPMS sensor IDs
• Display tire pressure reported by the TPMS sensor
• Read TPMS DTCs
• Register TPMS sensor IDs
1.
COLLECT INFORMATION FROM CUSTOMER
Get detailed information from the customer about the symptom (the condition and the environment when the
incident/malfunction occurred).
>> GO TO 2.
2.
TIRE PRESSURE INSPECTION
Check the tire pressure for all wheels. Refer to
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> Repair or replace tire(s) or wheel(s).
3.
CHECK LOW TIRE PRESSURE WARNING LAMP
Check that the low tire pressure warning lamp illuminates for approximately 1 second after the ignition switch
is turned ON, then turns OFF.
Does the low tire pressure warning lamp turn OFF?
YES
>> Inspection End.
NO
>> GO TO 4.
4.
PERFORM SELF DIAGNOSTIC RESULT
Perform “Self Diagnostic Result”. Refer to
.
Are any DTCs displayed?
YES
>> Refer to
. If two or more DTCs are displayed, refer to
"DTC Inspection Priority Chart"
.
NO
>> GO TO 5.
5.
PERFORM DIAGNOSIS APPLICABLE TO THE SYMPTOM
Perform diagnosis applicable to the symptom. Refer to
>> GO TO 6.
6.
FINAL CHECK
Perform “Self Diagnostic Result” again, and check that the malfunction is repaired. After checking, erase the
self diagnosis memory. Refer to
>> Inspection End.
ADDITIONAL SERVICE WHEN REPLACING BCM
WT-25
< BASIC INSPECTION >
C
D
F
G
H
I
J
K
L
M
A
B
WT
N
O
P
ADDITIONAL SERVICE WHEN REPLACING BCM
Description
INFOID:0000000011280499
When replacing BCM, configuration (BCM and TPMS) and then tire pressure sensor ID registration is
required.
Work Procedure
INFOID:0000000011280500
1.
PERFORM CONFIGURATION (BCM)
Perform configuration BCM. Refer to
BCS-61, "CONFIGURATION (BCM) : Work Procedure"
>> GO TO 2.
2.
PERFORM CONFIGURATION (TIRE PRESSURE MONITORING SYSTEM)
Perform configuration tire pressure monitoring system. Refer to
>> GO TO 3.
3.
PERFORM TIRE PRESSURE SENSOR ID REGISTRATION
Perform tire pressure sensor ID registration. Refer to
.
>> Work End.
WT-26
< BASIC INSPECTION >
ID REGISTRATION PROCEDURE
ID REGISTRATION PROCEDURE
Description
INFOID:0000000011280501
This procedure must be performed after replacement of a tire pressure sensor or BCM.
Work Procedure
INFOID:0000000011280502
TPMS ID registration can be performed using one of the following procedures:
• Transmitter Activation tool [KV48105501 (J-45295-A)] using CONSULT (preferred method)
• Signal Tech II tool [– (J-50190)] using CONSULT (preferred method)
• Signal Tech II tool [– (J-50190)] without CONSULT
• CONSULT only
TPMS REGISTRATION WITH TRANSMITTER ACTIVATION TOOL [KV48105501 (J-45295-A)]
With CONSULT
1. Turn the ignition switch ON.
2. Using CONSULT, select “Work support” in “AIR PRESSURE MONITOR”. Then, select “ID REGIST.”
3. Select “Start” on “ID REGIST” screen.
4. Hold the transmitter activation tool [KV48105501 (J-45295-A)]
(1) against the side of the left front tire, near the valve stem.
5. With the tool held at a 0 to 15 degree angle to the tire, press and
hold the transmitter activation tool button until the indicator lamp
turns OFF (approximately 5 seconds).
6. Repeat steps 4 and 5 for the remaining tires in this order: right
front, right rear and left rear.
7. When ID registration is complete, check the following pattern at each wheel.
8. After the ID registration procedure for all wheels is complete, press “End” on the CONSULT to finish ID
registration.
9. Test drive the vehicle to ensure that the TPMS lamp is OFF and no warning messages are present.
TPMS REGISTRATION WITH SIGNAL TECH II TOOL [– (J-50190)]
NOTE:
The Signal Tech II must be updated with the newest software version in order to perform the below proce-
dures. The Signal Tech II software updates can only be downloaded from a CONSULT unit with ASIST. Other
versions of ASIST will not show the updates.
With CONSULT
1. Adjust the tire pressure for all tires to the recommended value. Refer to
2. Turn the ignition switch ON.
3. Using CONSULT, select “Work support” in “AIR PRESSURE MONITOR”. Then, select “ID REGIST.”
4. Select “Start” on “ID REGIST” screen.
5. Turn on the Signal Tech II tool [– (J-50190)].
NNEIC0020ZZ
Sequence
ID registration position
Turn signal lamp
CONSULT
1
Front LH
2 blinks
“Yet (red)”
↓
“Done (green)”
2
Front RH
3
Rear RH
4
Rear LH
ID REGISTRATION PROCEDURE
WT-27
< BASIC INSPECTION >
C
D
F
G
H
I
J
K
L
M
A
B
WT
N
O
P
6. Hold the Signal Tech II against the side of the left front tire, near
the valve stem.
7. With the tool held at a 0 to 15 degree angle to the tire, select
“Activate Sensor” from the main menu, then press and release
the “OK” button to activate the sensor. Once the sensor is acti-
vated, the vehicle parking lamps will flash and the sensor ID will
appear on the CONSULT screen.
8. Repeat steps 6 and 7 for the remaining tires in this order: right
front, right rear and left rear.
9. When ID registration is complete, check the following pattern at
each wheel.
10. Once all sensors have been activated, select “End” on the CONSULT to finish ID registration.
11. Test drive the vehicle to ensure that the TPMS lamp is OFF and no warning messages are present.
Without CONSULT
1. Adjust the tire pressure for all tires to the recommended value. Refer to
2. Turn on the Signal Tech II tool [– (J-50190)] and select “TPMS Check” from the main menu.
3. Select vehicle model and year.
4. When prompted, hold the Signal Tech II against the side of the
left front tire, near the valve stem.
5. With the tool held at a 0 to 15 degree angle to the tire, press and
release the “OK” button to activate the sensor. Once the sensor
is activated, the tool will sound a tone and the tire pressure will
be displayed.
6. Repeat steps 4 and 5 for the remaining tires in this order: right
front, right rear and left rear.
7. When prompted, connect the tool to the data link connector. The
tool will connect to the BCM, read the VIN, read sensor IDs and
check for TPMS DTCs. Along with DTCs detected, one of the
following will be displayed next to each wheel:
-
N/A - Not applicable because no ID found by the tool
-
OK - Wheel and sensor are in original position
-
NEW - New ID found compared to BCM
-
RT - Wheel has been rotated
-
Low Press - Low tire pressure
8. If no DTC is present or the repair has been completed, press the “OK” button to register the IDs and clear
DTCs.
9. Test drive the vehicle to ensure that the TPMS lamp is OFF and no warning messages are present.
10. Print a Signal Tech II Audit Report for your records. Refer to the Signal Tech II User Guide for instructions.
TPMS REGISTRATION WITH CONSULT ONLY
With CONSULT
1. Adjust the tire pressure for all wheels to match the list below.
ALEIA0177ZZ
Sequence
ID registration position
Turn signal lamp
CONSULT
1
Front LH
2 blinks
“Yet (red)”
↓
“Done (green)”
2
Front RH
3
Rear RH
4
Rear LH
ALEIA0177ZZ
Tire position
Tire pressure kPa (kg/cm
2
, psi)
Front LH
240 (2.4, 35)
Front RH
220 (2.2, 32)
Rear RH
200 (2.0, 29)
Rear LH
180 (1.8, 26)
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст