Nissan Rogue. Manual — part 1238
WT-28
< BASIC INSPECTION >
ID REGISTRATION PROCEDURE
2. Turn the ignition switch ON.
3. Using CONSULT, select “Work support” in “AIR PRESSURE MONITOR”. Then, select “ID REGIST.”
4. Select “Start” on “ID REGIST” screen.
5. Drive the vehicle at a speed greater than 40 km/h (25 MPH) for 3 minutes or more.
6. After ID registration for all wheels is complete, press “End” on the CONSULT to finish ID registration.
7. Adjust the tire pressures for all tires to the recommended value. Refer to
8. Test drive the vehicle to ensure that the TPMS lamp is OFF and no warning messages are present.
ID registration position
CONSULT
Front LH
“Yet (red)”
↓
“Done (green)”
Front RH
Rear RH
Rear LH
CONFIGURATION (TIRE PRESSURE MONITORING SYSTEM)
WT-29
< BASIC INSPECTION >
C
D
F
G
H
I
J
K
L
M
A
B
WT
N
O
P
CONFIGURATION (TIRE PRESSURE MONITORING SYSTEM)
Work Procedure
INFOID:0000000011280503
CAUTION:
• After configuration, perform the following:
- Turn the ignition switch from OFF to ON and check that the low tire pressure warning lamp turns
OFF after staying illuminated for approximately two seconds.
- Perform tire pressure sensor ID registration. Refer to
• If TPMS configuration is not completed, TPMS transmitter ID registration will not complete.
1.
CHECKING ECU IDENTIFICATION NUMBER
CONSULT
1. Select “ECU Identification” of “BCM”.
2. Write down ECU part number.
>> GO TO 2.
2.
RE/PROGRAMMING, CONFIGURATION
CONSULT
1. Select “Re/programming, Configuration” from home screen.
2. Check box confirming the precautions have been read.
3. Select “Next”.
Is “Manual Selection (Vehicle Name)” displayed?
YES
>> GO TO 3.
NO
>> GO TO 4.
3.
VEHICLE SELECTION
CONSULT
1. Select Vehicle Make, Vehicle Name, and correct model year.
2. Press “Select”.
>> GO TO 4.
4.
VEHICLE CONFIRMATION
CONSULT
1. Verify VIN or Chassis Number matches the vehicles VIN.
2. Select “Confirm”.
>> GO TO 5.
5.
INPUT VIN
1. Verify VIN number in dialog box matches vehicles VIN.
2. Select “Confirm”.
>> GO TO 6.
6.
VEHICLE SELECTION
CONSULT
Select “AIR PRESSURE MONITOR”.
>> GO TO 7.
7.
OPERATION SELECTION
1. Select “Manual Configuration”
2. Select the DATA PART NO. that matches the BCM part number written down in step 1.
3. Select “Next”.
WT-30
< BASIC INSPECTION >
CONFIGURATION (TIRE PRESSURE MONITORING SYSTEM)
>> GO TO 8.
8.
WRITE CONFIGURATION
CONSULT
1. Confirm that the correct DATA PART NO. is listed.
2. Select “OK”.
>> GO TO 9.
9.
CHECKING LOW TIRE PRESSURE WARNING LAMP
1. Turn the ignition switch OFF.
2. Turn the ignition switch ON and check that the low tire pressure warning lamp turns OFF after staying illu-
minated for approximately two seconds.
CAUTION:
Never start the engine.
Is the inspection result normal?
YES
>> GO TO 10.
NO
>> Perform the “Self Diagnostic Result” in “AIR PRESSURE MONITOR”. Refer to
.
10.
PERFORMING SUPPLEMENTARY WORK
1. Perform tire pressure sensor ID registration. Refer to
.
2. Perform the self-diagnosis of all systems.
3. Erase self-diagnosis results.
>> End of work.
C1704, C1705, C1706, C1707 LOW TIRE PRESSURE
WT-31
< DTC/CIRCUIT DIAGNOSIS >
C
D
F
G
H
I
J
K
L
M
A
B
WT
N
O
P
DTC/CIRCUIT DIAGNOSIS
C1704, C1705, C1706, C1707 LOW TIRE PRESSURE
DTC Logic
INFOID:0000000011280504
NOTE:
The Signal Tech II Tool [– (J-50190)] can be used to perform the following functions. Refer to the Signal Tech
II User Guide for additional information.
• Activate and display TPMS sensor IDs
• Display tire pressure reported by the TPMS sensor
• Read TPMS DTCs
• Register TPMS sensor IDs
DTC DETECTION LOGIC
DTC CONFIRMATION PROCEDURE
1.
PERFORM SELF DIAGNOSTIC RESULT
With CONSULT
1. Check tire pressure for all wheels and adjust to the specified value. Refer to
2. Drive at a speed of 40 km/h (25 MPH) or more for 3 minutes, and then drive the vehicle at any speed for
10 minutes.
3. Perform “Self Diagnostic Result”.
Is DTC C1704, C1705, C1706, or C1707 detected?
YES
>> Proceed to
.
NO
>> Inspection End.
Diagnosis Procedure
INFOID:0000000011280505
NOTE:
The Signal Tech II Tool [– (J-50190)] can be used to perform the following functions. Refer to the Signal Tech
II User Guide for additional information.
• Activate and display TPMS sensor IDs
• Display tire pressure reported by the TPMS sensor
• Read TPMS DTCs
• Register TPMS sensor IDs
1.
TIRE PRESSURE SENSOR ID REGISTRATION
Perform tire pressure sensor ID registration. Refer to
.
Can the tire pressure sensor ID registration be completed?
YES
>> GO TO 2.
NO
>> Replace applicable tire pressure sensor. Refer to
WT-68, "Removal and Installation"
2.
CHECK TIRE PRESSURE
Check the air pressure of all wheels. Refer to
.
Is the inspection result normal?
DTC
Display Item
Malfunction Detected Condition
Possible Cause
C1704
LOW PRESSURE FL
Front LH tire pressure drops to 187.5 kPa (26.5
psi) or less.
• Low tire pressure
• Tire pressure sensor
C1705
LOW PRESSURE FR
Front RH tire pressure drops to 187.5 kPa (26.5
psi) or less.
C1706
LOW PRESSURE RR
Rear RH tire pressure drops to 187.5 kPa (26.5
psi) or less.
C1707
LOW PRESSURE RL
Rear LH tire pressure drops to 187.5 kPa (26.5
psi) or less.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст