Nissan Rogue. Manual — part 117
BCS-74
< SYMPTOM DIAGNOSIS >
[WITH INTELLIGENT KEY SYSTEM]
NORMAL OPERATING CONDITION
NORMAL OPERATING CONDITION
Description
INFOID:0000000011280227
SHIPPING MODE
• Shipping mode inhibits battery power consumption during transportation or storage of the vehicle. Vehicle is
set to shipping mode before being shipped from the factory.
• When ignition switch is OFF, BCM operates shipping mode.
• BCM control function is limited in shipping mode. Remote keyless entry function is not operated during the
shipping mode.
• For shipping mode cancel operation, refer to
.
NOTE:
Do not cancel shipping mode during storage of the vehicle. Always cancel shipping mode before delivery of
the vehicle to customer.
BCS
BCM (BODY CONTROL MODULE)
BCS-75
< REMOVAL AND INSTALLATION >
[WITH INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
K
L
B
A
O
P
N
REMOVAL AND INSTALLATION
BCM (BODY CONTROL MODULE)
Removal and Installation
INFOID:0000000011280228
CAUTION:
Before replacing the BCM, perform “READ CONFIGURATION” to save or print current vehicle specifi-
cation. Refer to
BCS-120, "ADDITIONAL SERVICE WHEN REPLACING CONTROL UNIT (BCM) : Work
.
REMOVAL
1. Disconnect the negative battery terminal. Refer to
PG-80, "Removal and Installation"
2. Remove the front kicking plate (LH). Refer to
INT-23, "KICKING PLATE : Removal and Installation - Front
.
3. Remove the dash side finisher (LH). Refer to
INT-24, "DASH SIDE FINISHER : Removal and Installation"
.
4. Disconnect the fuse box and the harness connectors.
5. Remove the instrument lower panel LH. Refer to
IP-23, "Removal and Installation"
.
6. Remove the bolt (A), then pull out the BCM (1).
7. Disconnect the harness connectors from the BCM and remove.
INSTALLATION
Installation is in the reverse order of removal.
CAUTION:
• When replacing BCM, perform “WRITE CONFIGURATION” Refer to
• When replacing BCM, perform the system initialization (NATS). Refer to
VICE WHEN REPLACING CONTROL UNIT (BCM) : Work Procedure"
• When replacing BCM, if new BCM does not come with Intelligent keys attached, all existing Intelli-
gent keys must be re-registered. Refer to the CONSULT immobilizer mode and follow the on screen
instructions.
ALMIA0690ZZ
BCS-76
< REMOVAL AND INSTALLATION >
[WITH INTELLIGENT KEY SYSTEM]
COMBINATION SWITCH
COMBINATION SWITCH
Exploded View
INFOID:0000000011280229
Removal and Installation
INFOID:0000000011280230
REMOVAL
1. Remove the steering angle sensor. Refer to
BRC-137, "Removal and Installation"
.
2. Disconnect harness connector from combination switch.
3. Remove screw (A) and combination switch (1).
INSTALLATION
Installation is in the reverse order of removal.
1.
Combination switch
2. Steering column
A. Screw
Front
AWMIA1520ZZ
AWMIA0709ZZ
BCS
PRECAUTIONS
BCS-77
< PRECAUTION >
[WITHOUT INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
K
L
B
A
O
P
N
PRECAUTION
PRECAUTIONS
Precaution for Supplemental Restraint System (SRS) "AIR BAG" and "SEAT BELT
PRE-TENSIONER"
INFOID:0000000011280231
The Supplemental Restraint System such as “AIR BAG” and “SEAT BELT PRE-TENSIONER”, used along
with a front seat belt, helps to reduce the risk or severity of injury to the driver and front passenger for certain
types of collision. Information necessary to service the system safely is included in the SR and SB section of
this Service Manual.
WARNING:
• To avoid rendering the SRS inoperative, which could increase the risk of personal injury or death in
the event of a collision which would result in air bag inflation, all maintenance must be performed by
an authorized NISSAN/INFINITI dealer.
• Improper maintenance, including incorrect removal and installation of the SRS, can lead to personal
injury caused by unintentional activation of the system. For removal of Spiral Cable and Air Bag
Module, see the SR section.
• Do not use electrical test equipment on any circuit related to the SRS unless instructed to in this
Service Manual. SRS wiring harnesses can be identified by yellow and/or orange harnesses or har-
ness connectors.
PRECAUTIONS WHEN USING POWER TOOLS (AIR OR ELECTRIC) AND HAMMERS
WARNING:
• When working near the Airbag Diagnosis Sensor Unit or other Airbag System sensors with the Igni-
tion ON or engine running, DO NOT use air or electric power tools or strike near the sensor(s) with a
hammer. Heavy vibration could activate the sensor(s) and deploy the air bag(s), possibly causing
serious injury.
• When using air or electric power tools or hammers, always switch the Ignition OFF, disconnect the
battery and wait at least three minutes before performing any service.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст