Nissan Rogue. Manual — part 679
FRONT WHEEL HUB
FAX-9
< REMOVAL AND INSTALLATION >
[FWD]
C
E
F
G
H
I
J
K
L
M
A
B
FAX
N
O
P
REMOVAL AND INSTALLATION
FRONT WHEEL HUB
Exploded View
INFOID:0000000011278623
Removal and Installation
INFOID:0000000011278624
REMOVAL
1. Remove front wheel and tire using power tool. Refer to
WT-67, "Removal and Installation"
2. Remove the bolt (1) and separate the front wheel sensor from
the steering knuckle. Refer to
.
CAUTION:
• Failure to separate the front wheel sensor from the steer-
ing knuckle may result in damage to the front wheel sen-
sor.
• Pull out the front wheel sensor, being careful to turn it as
little as possible. Do not pull on wheel sensor harness.
3. Remove brake caliper torque member bolts, leaving brake hose attached. Position the brake caliper aside
BR-37, "BRAKE CALIPER ASSEMBLY (1 PISTON TYPE) : Exploded View"
(1 PISTON
TYPE), or
BR-42, "BRAKE CALIPER ASSEMBLY (2 PISTON TYPE) : Exploded View"
(2 PISTON TYPE).
CAUTION:
Do not depress brake pedal while brake caliper is removed.
1.
Disc brake rotor
2.
Nut retainer
3.
Cotter pin
4.
Wheel stud
5.
Steering knuckle
6.
Splash guard
7.
Wheel hub and bearing
A. Wheel hub lock nut
ALDIA0488ZZ
ALDIA0526ZZ
FAX-10
< REMOVAL AND INSTALLATION >
[FWD]
FRONT WHEEL HUB
4. Put alignment marks (A) on disc brake rotor and wheel hub and
bearing. Remove disc brake rotor.
CAUTION:
Do not drop the disc brake rotor.
5. Remove cotter pin.
6. Remove the nut retainer.
7. Loosen the wheel hub lock nut from the drive shaft using power tool.
8. Using a piece of wood and a suitable tool, tap on the lock nut to
disengage the drive shaft from the wheel hub and bearing.
CAUTION:
• Do not place the drive shaft joint at an extreme angle. Be
careful not to over extend the slide joint.
• Do not allow the drive shaft to hang without support.
NOTE:
Use a suitable puller if drive shaft cannot be separated from the
wheel hub and bearing.
9. Remove the wheel hub lock nut.
10. Remove the engine side cover. Refer to
EXT-28, "FENDER PROTECTOR : Exploded View"
.
11. Remove the lower nut and bolt from the steering knuckle. Refer to
12. Separate transverse link from steering knuckle. Refer to
.
13. Separate drive shaft from wheel hub and bearing. Reposition the drive shaft aside with wire. Refer to
14. Remove the wheel hub and bearing bolts using power tool.
15. Remove the splash guard and the wheel hub and bearing from the steering knuckle.
16. If necessary, remove the wheel studs (1) using a suitable tool
(A).
INSPECTION AFTER REMOVAL
Check the following items, and replace the part if necessary.
• Check components for deformation, cracks, and other damage.
• Check boots of transverse link ball joint for cracks, axial end play, and swinging torque. Refer to
INSTALLATION
Installation is in the reverse order of the removal.
CAUTION:
• Do not reuse the wheel stud.
• Do not reuse the cotter pin.
JPDIG0066ZZ
JPDIG0070ZZ
JPDIF0299ZZ
FRONT WHEEL HUB
FAX-11
< REMOVAL AND INSTALLATION >
[FWD]
C
E
F
G
H
I
J
K
L
M
A
B
FAX
N
O
P
• Place a washer (A) as shown to install the wheel studs (1) by using
the tightening force of the nut (B).
CAUTION:
Check that there is no clearance between the wheel stud and
the wheel hub and bearing.
• Clean the mating surfaces of the wheel hub lock nut and the wheel hub and bearing.
CAUTION:
Do not apply lubricating oil to these mating surfaces.
• Clean the mating surfaces of the joint sub-assembly and the wheel
hub and bearing. Apply Molykote M77 lubricant to the surface (A)
of the joint sub-assembly.
CAUTION:
Apply lubricant to cover the entire flat mating surface of the
joint sub-assembly.
NOTE:
Always check with the Parts Department for the latest parts infor-
mation.
• Hold the wheel hub and bearing using a suitable tool. Tighten the wheel hub lock nut.
CAUTION:
• Since the drive shaft is assembled by press-fitting, use a torque wrench to tighten the wheel hub
lock nut. Do not use a power tool.
• Too much torque causes axle noise. Too little torque causes wheel bearing looseness. Tighten the
wheel hub lock nut to the specification.
• When installing the cotter pin (1) and the nut retainer (2), securely
bend the cotter pin to prevent rattles.
• Align the matching marks (A) on the disc brake rotor and on the
wheel hub and bearing.
• Complete the inspection. Refer to
.
JPDIF0300ZZ
JPDIG0122ZZ
JPDIF0295ZZ
JPDIG0066ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст