Nissan Rogue. Manual — part 1209
TM-208
< REMOVAL AND INSTALLATION >
[CVT: RE0F10D]
PRIMARY SPEED SENSOR
PRIMARY SPEED SENSOR
Exploded View
INFOID:0000000011279431
Removal and Installation
INFOID:0000000011279432
REMOVAL
1. Remove the engine undercover. Refer to
EXT-37, "ENGINE UNDER COVER : Removal and Installation"
2. Disconnect the primary speed harness connector.
3. Remove the primary speed sensor bolt and remove the primary speed sensor.
4. Remove the O-ring from the primary speed sensor.
INSTALLATION
Installation is in the reverse order of removal.
CAUTION:
• Do not reuse O-ring.
• Apply CVT fluid to the O-ring.
Inspection and Adjustment
INFOID:0000000011279433
INSPECTION AFTER INSTALLATION
Check for CVT fluid leakage. Refer to
.
ADJUSTMENT AFTER INSTALLATION
Adjust the CVT fluid level. Refer to
.
Transaxle assembly
O-ring
Primary speed sensor
: Always replace after every disassembly.
: N·m (kg-m, in-lb)
: Apply CVT fluid
JSDIA5141GB
OUTPUT SPEED SENSOR
TM-209
< REMOVAL AND INSTALLATION >
[CVT: RE0F10D]
C
E
F
G
H
I
J
K
L
M
A
B
TM
N
O
P
OUTPUT SPEED SENSOR
Exploded View
INFOID:0000000011279434
Removal and Installation
INFOID:0000000011279435
REMOVAL
1. Remove engine undercover. Refer to
TM-209, "Removal and Installation"
2. Disconnect the output speed sensor harness connector.
3. Remove the output speed sensor bolt and remove the output speed sensor.
4. Remove the O-ring from the output speed sensor.
INSTALLATION
Installation is in the reverse order of removal.
CAUTION:
• Do not reuse O-ring.
• Apply CVT fluid to the O-ring.
Inspection and Adjustment
INFOID:0000000011279436
INSPECTION AFTER INSTALLATION
Check for CVT fluid leakage. Refer to
.
ADJUSTMENT AFTER INSTALLATION
Adjust the CVT fluid level. Refer to
.
Transaxle assembly
Output speed sensor
O-ring
: Always replace after every disassembly.
: N·m (kg-m, in-lb)
: Apply CVT fluid
JSDIA5033GB
TM-210
< REMOVAL AND INSTALLATION >
[CVT: RE0F10D]
DIFFERENTIAL SIDE OIL SEAL
DIFFERENTIAL SIDE OIL SEAL
Exploded View
INFOID:0000000011279437
Removal and Installation
INFOID:0000000011279438
REMOVAL
NOTE:
When removing components such as hoses, tubes/lines, etc., cap or plug openings to prevent fluid from spill-
ing.
1. Remove front drive shaft. Refer to
FAX-19, "Removal and Installation (LH)"
(FWD) or
[LH (AWD)] or
FAX-61, "Removal and Installation (RH)"
[RH(AWD)].
2. Remove differential side oil seal (1) using suitable tool (A).
CAUTION:
Be careful not to scratch transaxle case and converter
housing.
INSTALLATION
Installation is in the reverse order of removal.
CAUTION:
• Do not reuse differential side oil seal.
• Apply CVT fluid to differential side oil seals.
• When inserting the drive shaft, be sure to use Tool.
Transaxle assembly
Differential side oil seal (left side)
Differential side oil seal (right side)
(FWD models only)
: Always replace after every disassembly.
: Apply CVT fluid
JSDIA3729GB
JPDIA0118ZZ
Tool number
: KV38107900
DIFFERENTIAL SIDE OIL SEAL
TM-211
< REMOVAL AND INSTALLATION >
[CVT: RE0F10D]
C
E
F
G
H
I
J
K
L
M
A
B
TM
N
O
P
Install each differential side oil seal evenly using suitable tool so that
differential side oil seal protrudes by the dimension (C) and (D)
respectfully.
NOTE:
The reference is the installation direction of the differential side oil seal.
Drift to be used:
Inspection and Adjustment
INFOID:0000000011279439
INSPECTION AFTER INSTALLATION
Check for CVT fluid leakage. Refer to
.
ADJUSTMENT AFTER INSTALLATION
Adjust the CVT fluid level. Refer to
.
(A)
: Differential side oil seal (LH)
(B)
: Differential side oil seal (RH) (FWD models only)
ALDIA0400ZZ
Dimension (C)
:Height difference from case end surface is within 1.8
± 0.5 mm (0.071 ±
0.020 in).
Dimension (D)
:Height difference from case end surface is within 2.2
± 0.5 mm (0.087 ±
0.020 in).
Location
Commercial Service Tools
Transaxle case side
Commercial service tool with outer dia. 56 mm (2.20 in) and in-
ner dia. 50 mm (1.97 in)
Converter housing side
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст