Nissan Rogue. Manual — part 1210
TM-212
< REMOVAL AND INSTALLATION >
[CVT: RE0F10D]
WATER HOSE
WATER HOSE
Exploded View
INFOID:0000000011279440
Removal and Installation
INFOID:0000000011279441
REMOVAL
WARNING:
Do not remove the radiator cap when the engine is hot. Serious burns could occur from high pressure
engine coolant escaping from the radiator. Wrap a thick cloth around the cap. Slowly turn it a quarter
turn to allow built-up pressure to escape. Carefully remove the cap by turning it all the way.
CAUTION:
Perform when the engine is cold.
NOTE:
When removing components such as hoses, tubes/lines, etc., cap or plug openings to prevent fluid from spill-
ing.
1. Remove battery tray. Refer to
PG-79, "Removal and Installation (Battery Tray)"
2. Remove engine under cover. Refer to
.
3. Remove CVT fluid charging pipe. Refer to
4. Remove fender protector side cover. Refer to
EXT-28, "FENDER PROTECTOR : Exploded View"
5. Remove water hose A, B, C, and heater thermostat.
INSTALLATION
Installation is in the reverse order of removal.
Water outlet
Hose clamp
Water hose A
Clip
CVT oil warmer
Transaxle assembly
Water hose B
Heater thermostat
Water hose C
: Always replace after every disassembly.
: N·m (kg-m, ft-lb)
JSDIA5142GB
WATER HOSE
TM-213
< REMOVAL AND INSTALLATION >
[CVT: RE0F10D]
C
E
F
G
H
I
J
K
L
M
A
B
TM
N
O
P
CAUTION:
• Do not reuse hose clamps.
• Do not reuse hose clip
• Securely install the water hose clip to the bracket hole of charging pipe.
• Refer to the following when installing water hoses.
• Refer to the followings when installing hose clamp.
CAUTION:
Hose clamp should not interfere with the bulge of tube.
Inspection
INFOID:0000000011279442
INSPECTION AFTER REMOVAL
Heater Thermostat
1. Fully immerse the heater thermostat in a container (A) filled
with water. Continue heating the water while stirring.
2. Continue heating the heater thermostat for 5 minutes or more
after bringing the water to a boil.
3. Quickly take the heater thermostat out of the hot water, measure the heater thermostat within 10 seconds.
Water hose (1)
Installation side
tube (2)
Direction of paint
mark
Hose insertion depth
(L)
Water hose A
Water outlet
Upward
End reaches the end
of tube.
CVT oil warmer
Frontward
End reaches the 2-
stage bulge.
Water hose B
CVT oil warmer
Frontward
Heater thermostat
Align with the mark
on the heater ther-
mostat
Water hose C
Heater thermostat
Align with the mark
on the heater ther-
mostat
End reaches the ex-
pansion part.
Water outlet
Upward
End reaches the 2-
stage bulge.
Water hose (1)
Installation side tube
(2)
Hose clamp (3)
Direction of tab
Clamping position
Water hose A
Water outlet
Upward
5 – 7 mm (0.20 –
0.28 in) (A) from
hose end
CVT oil warmer
Leftward
Water hose B
CVT oil warmer
Leftward
5 – 9 mm (0.20 –
0.35 in) (A) from
hose end
Heater thermostat
Align with the mark
on the hose
Water hose C
Heater thermostat
Align with the mark
on the hose
Water outlet
Forward and 45
° up-
ward
JSDIA2459ZZ
JSDIA2424ZZ
JSDIA3661ZZ
TM-214
< REMOVAL AND INSTALLATION >
[CVT: RE0F10D]
WATER HOSE
-
Place dial indicator (A) on the pellet and measure the elonga-
tion from the initial state.
4. If out of standard, replace heater thermostat.
INSPECTION AFTER INSTALLATION
Start the engine, and check the joints for coolant leakage.
Standard
.
JSDIA3662ZZ
FLUID COOLER HOSE
TM-215
< REMOVAL AND INSTALLATION >
[CVT: RE0F10D]
C
E
F
G
H
I
J
K
L
M
A
B
TM
N
O
P
FLUID COOLER HOSE
Exploded View
INFOID:0000000011279443
COMPONENT PARTS LOCATION
Removal and Installation
INFOID:0000000011279444
REMOVAL
NOTE:
When removing components such as hoses, tubes/lines, etc., cap or plug openings to prevent fluid from spill-
ing.
1. Remove engine under cover. Refer to
EXT-37, "ENGINE UNDER COVER : Removal and Installation"
.
2. Remove fender protector side cover. Refer to
EXT-28, "FENDER PROTECTOR : Exploded View"
3. Remove fluid cooler hoses.
INSTALLATION
Installation is in the reverse order of removal.
CAUTION:
• Do not reuse hose clamp.
• Securely install fluid cooler hose A clip to the radiator core support.
• Refer to the followings when installing fluid cooler hoses.
Transaxle assembly
Fluid cooler hose A
Hose clamp
Fluid cooler hose B
CVT oil warmer
To radiator
: Always replace after every disassembly.
JSDIA5143ZZ
Fluid cooler
hose (1)
Installation side
tube (2)
Direction of
paint mark
Hose insertion depth (L)
Fluid cooler
hose A
CVT oil warmer
Frontward
A: End reaches the 2 step
bulge
Radiator Downward
B: Insert the hose until hose
touches the radiator
Fluid cooler
hose B
Radiator Downward
B: Insert the hose until hose
touches the radiator
CVT oil warmer
Downward
A: End reaches the 2 step
bulge
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст