Nissan Rogue. Manual — part 235
DAS
U111A REAR CAMERA IMAGE SIGNAL CIRCUIT
DAS-111
< DTC/CIRCUIT DIAGNOSIS >
[DRIVER ASSISTANCE SYSTEM]
C
D
E
F
G
H
I
J
K
L
M
B
N
P
A
Is the inspection result normal?
YES
>> Replace around view monitor control unit. Refer to
AV-380, "Removal and Installation"
NO
>> Replace rear view camera. Refer to
AV-383, "Removal and Installation"
.
Around view monitor control unit connector M114
Condition
Reference value
(+)
(
−)
Terminal
Terminal
53
54
CAMERA switch is ON or se-
lector lever in R (reverse).
JSNIA0834GB
DAS-112
< DTC/CIRCUIT DIAGNOSIS >
[DRIVER ASSISTANCE SYSTEM]
U111B SIDE CAMERA RH IMAGE SIGNAL CIRCUIT
U111B SIDE CAMERA RH IMAGE SIGNAL CIRCUIT
DTC Logic
INFOID:0000000011419757
DTC DETECTION LOGIC
Diagnosis Procedure
INFOID:0000000011459688
Regarding Wiring Diagram information, refer to
.
WITHOUT DRIVER ASSISTANCE SYSTEM
1.
CHECK RH SIDE CAMERA POWER SUPPLY AND GROUND CIRCUIT CONTINUITY
1. Turn ignition switch OFF.
2. Disconnect around view monitor control unit and RH side camera connectors.
3. Check continuity between around view monitor control unit connector M103 and RH side camera connec-
tor D107.
4. Check continuity between around view monitor control unit connector M103 and ground.
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> Repair or replace harness or connectors.
2.
CHECK RH SIDE CAMERA POWER SUPPLY VOLTAGE
1. Connect around view monitor control unit and RH side camera connectors.
2. Turn ignition switch ON.
3. Check voltage between around view monitor control unit connector M103 and ground.
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> Replace around view monitor control unit. Refer to
AV-380, "Removal and Installation"
3.
CHECK RH SIDE CAMERA IMAGE SIGNAL AND IMAGE SIGNAL GROUND CIRCUIT CONTINUITY
1. Turn ignition switch OFF.
CONSULT Display
DTC Detection Condition
Possible Cause
Right side display output signal
diagnosis (Harness disconnec-
tion)
[U111B]
Right side camera image signal circuit open or
short.
Check right side camera image signal circuit.
Around view monitor control unit
RH side camera
Continuity
Connector
Terminals
Connector
Terminals
M103
34
D107
7
Yes
33
8
Around view monitor control unit
Ground
Continuity
Connector
Terminal
M103
34
No
Around view monitor control unit
Ground
Condition
Voltage
(Approx.)
Connector
Terminal
M103
34
—
CAMERA switch is ON or
selector lever in R (re-
verse).
6.0 V
DAS
U111B SIDE CAMERA RH IMAGE SIGNAL CIRCUIT
DAS-113
< DTC/CIRCUIT DIAGNOSIS >
[DRIVER ASSISTANCE SYSTEM]
C
D
E
F
G
H
I
J
K
L
M
B
N
P
A
2. Disconnect around view monitor control unit and RH side camera connectors.
3. Check continuity between around view monitor control unit connector M103 and RH side camera connec-
tor D107.
4. Check continuity between around view monitor control unit connector M103 and ground.
Is the inspection result normal?
YES
>> GO TO 4.
NO
>> Repair or replace harness or connectors.
4.
CHECK RH SIDE CAMERA IMAGE SIGNAL
1. Connect around view monitor control unit and RH side camera connectors.
2. Turn ignition switch ON.
3. Check signal between the terminals of around view monitor control unit connector M103.
Is the inspection result normal?
YES
>> Replace around view monitor control unit. Refer to
AV-380, "Removal and Installation"
NO
>> Replace RH side camera. Refer to
AV-382, "Removal and Installation"
WITH DRIVER ASSISTANCE SYSTEM
1.
CHECK RH SIDE CAMERA POWER SUPPLY AND GROUND CIRCUIT CONTINUITY
1. Turn ignition switch OFF.
2. Disconnect around view monitor control unit and RH side camera connectors.
3. Check continuity between around view monitor control unit connector M114 and RH side camera connec-
tor D107.
4. Check continuity between around view monitor control unit connector M114 and ground.
Around view monitor control unit
RH side camera
Continuity
Connector
Terminals
Connector
Terminals
M103
36
D107
16
Yes
35
15
Around view monitor control unit
Ground
Continuity
Connector
Terminal
M103
36
No
Around view monitor control unit connector M103
Condition
Reference value
(+)
(
−)
Terminal
Terminal
36
35
CAMERA switch is ON or se-
lector lever in R (reverse).
JSNIA0834GB
Around view monitor control unit
RH side camera
Continuity
Connector
Terminals
Connector
Terminals
M114
62
D107
7
Yes
64
8
DAS-114
< DTC/CIRCUIT DIAGNOSIS >
[DRIVER ASSISTANCE SYSTEM]
U111B SIDE CAMERA RH IMAGE SIGNAL CIRCUIT
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> Repair or replace harness or connectors.
2.
CHECK RH SIDE CAMERA POWER SUPPLY VOLTAGE
1. Connect around view monitor control unit and RH side camera connectors.
2. Turn ignition switch ON.
3. Check voltage between around view monitor control unit connector M114 and ground.
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> Replace around view monitor control unit. Refer to
AV-380, "Removal and Installation"
3.
CHECK RH SIDE CAMERA IMAGE SIGNAL AND IMAGE SIGNAL GROUND CIRCUIT CONTINUITY
1. Turn ignition switch OFF.
2. Disconnect around view monitor control unit and RH side camera connectors.
3. Check continuity between around view monitor control unit connector M114 and RH side camera connec-
tor D107.
4. Check continuity between around view monitor control unit connector M114 and ground.
Is the inspection result normal?
YES
>> GO TO 4.
NO
>> Repair or replace harness or connectors.
4.
CHECK RH SIDE CAMERA IMAGE SIGNAL
1. Connect around view monitor control unit and RH side camera connectors.
2. Turn ignition switch ON.
3. Check signal between the terminals of around view monitor control unit connector M114.
Around view monitor control unit
Ground
Continuity
Connector
Terminal
M114
62
No
Around view monitor control unit
Ground
Condition
Voltage
(Approx.)
Connector
Terminal
M114
62
—
CAMERA switch is ON or
selector lever in R (re-
verse).
6.0 V
Around view monitor control unit
RH side camera
Continuity
Connector
Terminals
Connector
Terminals
M114
65
D107
16
Yes
66
15
Around view monitor control unit
Ground
Continuity
Connector
Terminal
M114
65
No
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст