Nissan Rogue. Manual — part 932
MWI
THE FUEL GAUGE DOES NOT MOVE
MWI-75
< SYMPTOM DIAGNOSIS >
C
D
E
F
G
H
I
J
K
L
M
B
A
O
P
SYMPTOM DIAGNOSIS
THE FUEL GAUGE DOES NOT MOVE
Description
INFOID:0000000011279831
Fuel gauge does not move from a certain position.
Diagnosis Procedure
INFOID:0000000011279832
1.
CHECK COMBINATION METER INPUT SIGNAL
Perform component function check. Refer to
MWI-63, "Component Function Check"
.
Does monitor value match fuel gauge reading?
YES
>> GO TO 2.
NO
>> Replace combination meter. Refer to
MWI-84, "Removal and Installation"
2.
CHECK FUEL LEVEL SENSOR UNIT CIRCUITS
Check the fuel level sensor circuits. Refer to
.
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> Repair or replace harness or connector.
3.
CHECK FUEL LEVEL SENSOR UNIT
Check the fuel level sensor unit. Refer to
MWI-64, "Component Inspection"
.
Is the inspection result normal?
YES
>> GO TO 4.
NO
>> Replace fuel level sensor unit. Refer to
FL-5, "Removal and Installation"
.
4.
CHECK FLOAT INTERFERENCE
Check that the float arm does not interfere with or binds to other components in the fuel tank.
Is the inspection result normal?
YES
>> Check intermittent incident. Refer to
GI-44, "Intermittent Incident"
.
NO
>> Repair or replace malfunctioning parts.
MWI-76
< SYMPTOM DIAGNOSIS >
THE OIL PRESSURE WARNING CONTINUES DISPLAYING, OR DOES NOT DIS-
PLAY
THE OIL PRESSURE WARNING CONTINUES DISPLAYING, OR DOES
NOT DISPLAY
Description
INFOID:0000000011279833
• The low oil pressure warning message stays on when oil pressure is normal.
• The low oil pressure warning message stays off when oil pressure is low.
Diagnosis Procedure
INFOID:0000000011279834
1.
CHECK COMBINATION METER INPUT
1. Start the engine.
2. Select “METER/M&A” using CONSULT.
3. Select “OIL W/L” in “Data Monitor”.
4. Check the “OIL W/L” status according to the following condition:
Is the inspection result normal?
YES
>> Perform “Self Diagnosis” of “ECM”. Refer to
.
NO
>> Replace combination meter. Refer to
MWI-84, "Removal and Installation"
Monitor Item
Condition
CONSULT
OIL W/L
Engine running
Off
MWI
THE PARKING BRAKE RELEASE WARNING CONTINUES DISPLAYING, OR
DOES NOT DISPLAY
MWI-77
< SYMPTOM DIAGNOSIS >
C
D
E
F
G
H
I
J
K
L
M
B
A
O
P
THE PARKING BRAKE RELEASE WARNING CONTINUES DISPLAYING,
OR DOES NOT DISPLAY
Description
INFOID:0000000011279835
• The parking brake warning is displayed during vehicle travel even though the parking brake is released.
• The parking brake warning is not displayed even though driving the vehicle with the parking brake applied.
Diagnosis Procedure
INFOID:0000000011279836
1.
CHECK PARKING BRAKE WARNING LAMP OPERATION
1. Start engine.
2. Check the operation of the brake warning lamp while operating the parking brake.
Is the inspection result normal?
YES
>> Replace combination meter. Refer to
MWI-84, "Removal and Installation"
NO
>> GO TO 2.
2.
CHECK PARKING BRAKE SWITCH SIGNAL CIRCUIT
1. Turn ignition switch OFF.
2. Check the parking brake switch signal circuit. Refer to
.
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> Repair or replace harness or connector.
3.
CHECK PARKING BRAKE SWITCH UNIT
Check the parking brake switch. Refer to
MWI-65, "Component Inspection"
Is the inspection result normal?
YES
>> Replace combination meter. Refer to
MWI-84, "Removal and Installation"
NO
>> Replace parking brake switch. Refer to
.
Condition
Warning lamp status
Parking brake applied
ON
Parking brake released
OFF
MWI-78
< SYMPTOM DIAGNOSIS >
THE LOW WASHER FLUID WARNING CONTINUES DISPLAYING, OR DOES
NOT DISPLAY
THE LOW WASHER FLUID WARNING CONTINUES DISPLAYING, OR
DOES NOT DISPLAY
Description
INFOID:0000000011279837
• The warning is still displayed even after washer fluid is added.
• The warning is not displayed even though the washer tank is empty.
Diagnosis Procedure
INFOID:0000000011279838
1.
CHECK WASHER FLUID LEVEL SWITCH SIGNAL CIRCUIT
Check the washer fluid level switch signal circuit. Refer to
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> Repair or replace harness or connector.
2.
CHECK WASHER FLUID LEVEL SWITCH UNIT
Check the washer fluid level switch. Refer to
MWI-73, "Component Inspection"
Is the inspection result normal?
YES
>> Replace combination meter. Refer to
MWI-84, "Removal and Installation"
NO
>> Replace washer fluid level switch. Refer to
WW-57, "Removal and Installation"
.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст