Nissan Rogue. Manual — part 652
B1256 FRONT FOG LAMP RH POWER SUPPLY CIRCUIT
EXL-237
< DTC/CIRCUIT DIAGNOSIS >
[LED HEADLAMP]
C
D
E
F
G
H
I
J
K
M
A
B
EXL
N
O
P
B1256 FRONT FOG LAMP RH POWER SUPPLY CIRCUIT
DTC Logic
INFOID:0000000011421513
DTC DETECTION LOGIC
DTC CONFIRMATION PROCEDURE
1.
CHECK SELF DIAGNOSTIC RESULT
With
CONSULT.
1. Turn ignition switch ON.
2. Perform “Self Diagnostic Result”.
Is DTC B1256 detected?
YES
>> Proceed to diagnosis procedure. Refer to
EXL-237, "Diagnosis Procedure"
NO
>> Inspection End.
Diagnosis Procedure
INFOID:0000000011421514
1.
CHECK FOG LAMP SHORT CIRCUIT TO GROUND
1. Disconnect fog lamp connector and IPDM E/R connector.
2. Check continuity between IPDM E/R harness connector and ground.
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> Repair or replace harness.
2.
CHECK FOG LAMP SHORT CIRCUIT TO GROUND
1. Reconnect IPDM E/R connector.
2. Check continuity between fog lamp harness connector and ground.
Is the inspection result normal?
YES
>> Refer to
GI-44, "Intermittent Incident"
.
NO
>> Replace IPDM E/R. Refer to
PCS-40, "Removal and Installation"
.
DTC
Display Item
Malfunction detected condition
Possible causes
B1256
FR FOG LAMP RH PWR SPLY CIRC
[CIRC SHORT TO GRND]
When a short circuit to ground is detected.
• IPDM E/R
• Short to ground
IPDM E/R
Ground
Continuity
Connector
Terminal
E218
57
No
Fog lamp
Ground
Continuity
Connector
Terminal
RH
E221
1
No
EXL-238
< DTC/CIRCUIT DIAGNOSIS >
[LED HEADLAMP]
B1C00 HEIGHT SENSOR POWER SUPPLY CIRCUIT
B1C00 HEIGHT SENSOR POWER SUPPLY CIRCUIT
DTC Logic
INFOID:0000000011280867
DTC DETECTION LOGIC
DTC CONFIRMATION PROCEDURE
1.
CHECK SELF DIAGNOSTIC RESULT
With
CONSULT.
1. Turn ignition switch ON.
2. Perform “Self Diagnostic Result”.
Is DTC B1C00 detected?
YES
>> Proceed to diagnosis procedure. Refer to
EXL-238, "Diagnosis Procedure"
NO
>> Inspection End.
Diagnosis Procedure
INFOID:0000000011280868
1.
CHECK HEIGHT SENSOR SHORT CIRCUIT TO GROUND
1. Disconnect rear height sensor connector and IPDM E/R connector.
2. Check continuity between IPDM E/R harness connector and ground.
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> Repair or replace harness.
2.
CHECK HEIGHT SENSOR SHORT CIRCUIT TO BATTERY VOLTAGE
1. Reconnect IPDM E/R connector.
2. Check the voltage between IPDM E/R harness connector and ground.
Is the inspection result normal?
YES
>> Refer to
GI-44, "Intermittent Incident"
.
NO
>> Replace IPDM E/R. Refer to
PCS-40, "Removal and Installation"
DTC
Display Item
Malfunction detected condition
Possible causes
B1C00
HEIGHT SENSOR PWR SPLY CIRC
[CIRC SHORT TO GRND]
When the height sensor power supply circuit is short-
ed to supply power or shorted to ground
• Short to ground
• Short to supply voltage
HEIGHT SENSOR PWR SPLY CIRC
[CIRC SHORT TO BATTERY]
IPDM E/R
Ground
Continuity
Connector
Terminal
E120
25
No
IPDM E/R
Ground
Voltage
(Approx.)
Connector
Terminal
E120
25
0 V
B1C02 REAR HEIGHT SENSOR SIGNAL
EXL-239
< DTC/CIRCUIT DIAGNOSIS >
[LED HEADLAMP]
C
D
E
F
G
H
I
J
K
M
A
B
EXL
N
O
P
B1C02 REAR HEIGHT SENSOR SIGNAL
DTC Logic
INFOID:0000000011280869
DTC DETECTION LOGIC
DTC CONFIRMATION PROCEDURE
1.
CHECK SELF DIAGNOSTIC RESULT
1. Turn ignition switch ON.
2. Check “Self Diagnostic Result” with CONSULT.
Is DTC detected?
YES
>> Refer to
EXL-239, "Diagnosis Procedure"
.
NO
>> Inspection End.
Diagnosis Procedure
INFOID:0000000011280870
1.
CHECK HEIGHT SENSOR SHORT CIRCUIT TO GROUND
1. Disconnect rear height sensor connector and IPDM E/R connector.
2. Check continuity between IPDM E/R harness connector and ground.
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> Repair or replace harness.
2.
CHECK HEIGHT SENSOR SHORT OPEN CIRCUIT
Check the continuity between IPDM E/R harness connector and height sensor connector.
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> Repair or replace harness.
3.
CHECK HEIGHT SENSOR SHORT CIRCUIT TO BATTERY VOLTAGE
1. Reconnect IPDM E/R connector.
2. Check the voltage between IPDM E/R harness connector and ground.
DTC No.
Self-diagnosis item
DTC Detection Condition
Possible causes
B1C02
RR HEIGHT SENSOR SIGNAL
[CIRC SHORT TO BATTERY]
• Short to ground
• Short to supply voltage
• Circuit voltage out of range
• Harness or connectors between the rear height
sensor and the IPDM E/R
(The sensor circuit is open or shorted)
• IPDM E/R
• Height sensor
RR HEIGHT SENSOR SIGNAL
[CIRC SHORT TO GROUND OR
OPEN]
RR HEIGHT SENSOR SIGNAL
[CIRC VOLTAGE OUT OF
RANGE]
IPDM E/R
Ground
Continuity
Connector
Terminal
E120
21
No
IPDM E/R
Rear height sensor
Ground
Continuity
Connector
Terminal
Connector
Terminal
E120
21
B91
1
Yes
IPDM E/R
Ground
Voltage
(Approx.)
Connector
Terminal
E120
21
0 V
EXL-240
< DTC/CIRCUIT DIAGNOSIS >
[LED HEADLAMP]
B1C02 REAR HEIGHT SENSOR SIGNAL
Is the inspection result normal?
YES
>> Refer to
GI-44, "Intermittent Incident"
.
NO
>> Replace IPDM E/R. Refer to
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст