Nissan Rogue. Manual — part 700
FUEL TANK
FL-15
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
J
K
L
M
A
FL
N
P
O
AWD : Exploded View
INFOID:0000000011279619
AWD : Removal and Installation
INFOID:0000000011279620
WARNING:
Be sure to read “General Precautions” when working on the fuel system. Refer to
.
NOTE:
When removing components such as hoses, tubes/lines, etc., cap or plug openings to prevent fluid from spill-
ing.
REMOVAL
1.
Fuel filler cap
2.
Grommet
3.
Fuel filler tube
4.
Cover
5.
Clamp
6.
Fuel filler hose
7.
Clamp
8.
Vent hose
9.
Fuel tank protector
10. Fuel tank strap (LH)
11.
Fuel tank strap (RH)
12. Fuel tank
A.
To EVAP canister
AWBIA1953ZZ
FL-16
< REMOVAL AND INSTALLATION >
FUEL TANK
1. Check the fuel level with the vehicle on a level surface. If the fuel
gauge indicates more than the level as shown (1/2 full), drain
the fuel from the fuel tank until the fuel gauge indicates a level at
or below as shown (1/2 full).
• In case the fuel pump does not operate, use the following pro-
cedure.
a. Insert fuel tubing of less than 25mm (0.98in) diameter into the
fuel filler tube through the fuel filler opening to drain fuel from the
fuel filler tube.
b. Disconnect the fuel filler hose from the fuel filler tube.
c.
Insert fuel tubing into the fuel tank through the fuel filler hose to
drain fuel from the fuel tank.
• As a guide, the fuel level reaches or is less than the level on the fuel gauge as shown, when approxi-
mately 27.5 (7-1/4 US gal, 6 Imp gal) of fuel is drained from a full fuel tank.
2. Release the fuel pressure from the fuel lines. Refer to
.
3. Disconnect negative battery terminal. Refer to
PG-78, "Removal and Installation (Battery)"
.
4. Unscrew the fuel filler cap to release the pressure inside the fuel tank.
5. Remove second row seat (RH). Refer to
SE-39, "Removal and Installation"
6. Turn the four retainers 90 degrees to disengage the clips and remove the fuel pump inspection hole cover.
CAUTION:
Cover the immediate area surrounding the fuel pump inspection hole cover with plastic to avoid
gasoline damage to carpet.
7. Disconnect harness connector (A) and quick connector (B).
Disconnect quick connector as follows:
• Hold the sides of connector, press tabs and pull out fuel feed
tube.
• If quick connector sticks to tube of main fuel level sensor unit, push and pull quick connectors several
times until they start to move. Then disconnect them by pulling.
CAUTION:
: Front
ALBIA0787ZZ
JPBIA1266ZZ
(A)
: Pull
(B)
: Push in tabs
JPBIA0134ZZ
FUEL TANK
FL-17
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
J
K
L
M
A
FL
N
P
O
• Quick connector (1) can be disconnected when the tabs
(F) are depressed completely. Do not twist it more than
necessary.
• Do not use any tools to disconnected quick connector.
• Keep resin tube (C) away from heat. Be especially care-
ful when welding near the resin tube.
• Prevent acid liquid such as battery electrolyte, etc. from
getting on resin tube.
• Do not bend or twist resin tube during installation and
disconnection.
• Do not remove the remaining retainer (2) on hard tube
(or the equivalent) (A) except when resin tube or retainer
is replaced.
• When resin tube or hard tube (or the equivalent) is
replaced, also replace retainer with new one.
• To keep the connecting portion clean and to avoid dam-
age and foreign materials, cover them completely with
plastic bags (A) or something similar.
8. Remove center exhaust tube and muffler assembly. Refer to
.
9. Remove propeller shaft. Refer to
DLN-100, "Removal and Installation"
.
10. Remove protector from fuel tank.
11. Remove vent hose (1) at rear side of fuel tank.
12. Disconnect EVAP tube (2) at rear side of fuel tank.
• Instruction for quick connector (A) of EVAP tube. Refer to
.
13. Remove fuel filler hose (3) at fuel filler tube side.
14. Remove parking brake cable bolts and separate parking brake cable from suspension arm. Refer to
15. Remove lower link deflector. Refer to
.
(B)
: Connection (cross-section)
(D)
: To under floor fuel line
(E)
: To fuel tank
(G)
: Disconnection
JPBIA0130ZZ
JPBIA0135ZZ
: Front
JPBIA1269ZZ
FL-18
< REMOVAL AND INSTALLATION >
FUEL TANK
16. Support center of fuel tank (1) with suitable jack (A).
CAUTION:
Securely support the fuel tank with a piece of wood (B).
17. Remove fuel tank bands.
18. Lower suitable jack carefully to remove fuel tank while holding it by hand.
CAUTION:
Fuel tank may be in an unstable condition, due to the shape of the fuel tank bottom. Be sure to
secure tank at all times.
19. If replacing the fuel tank, remove the fuel level sensor unit, fuel filter and fuel pump assembly to transfer to
the new fuel tank. Remove and discard the O-ring. Refer to
FL-5, "Removal and Installation"
.
INSTALLATION
Installation is in the reverse order of removal.
Fuel Filler Hose
• Insert fuel filler hose to the length below.
• Be sure hose clamp is not placed on swelled area of fuel filler tube.
• Tighten the clamp hand with the top mark (A) until the mark is on
the bolt head flange.
AWD : Inspection
INFOID:0000000011279621
INSPECTION AFTER INSTALLATION
Use the following procedure to check for fuel leaks.
1. Turn the ignition switch ON (without starting the engine). Then check the connections for fuel leaks by
applying fuel pressure to the fuel piping.
2. Start engine, raise idle and verify there are no leaks at the fuel system connections.
ALBIA1196ZZ
: 35 mm (1.38 in)
JPBIA0146ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст