Nissan Rogue. Manual — part 691
FRONT DRIVE SHAFT
FAX-57
< REMOVAL AND INSTALLATION >
[AWD]
C
E
F
G
H
I
J
K
L
M
A
B
FAX
N
O
P
FRONT DRIVE SHAFT
Exploded View (LH)
INFOID:0000000011278654
Removal and Installation (LH)
INFOID:0000000011278655
REMOVAL
1. Remove front wheel and tire using power tool. Refer to
WT-67, "Removal and Installation"
2. Remove the bolt (1) and separate the front wheel sensor from
the steering knuckle. Refer to
.
CAUTION:
• Failure to separate the front wheel sensor from the steer-
ing knuckle may result in damage to the front wheel sen-
sor.
• Pull out the front wheel sensor, being careful to turn it as
little as possible. Do not pull on wheel sensor harness.
3. Remove brake caliper torque member bolts, leaving brake hose attached. Position the brake caliper aside
BR-37, "BRAKE CALIPER ASSEMBLY (1 PISTON TYPE) : Exploded View"
(1 PISTON
TYPE), or
BR-42, "BRAKE CALIPER ASSEMBLY (2 PISTON TYPE) : Exploded View"
(2 PISTON TYPE).
CAUTION:
Do not depress brake pedal while brake caliper is removed.
1.
Drive shaft
2.
Nut retainer
3.
Cotter pin
AWDIA1204ZZ
ALDIA0526ZZ
FAX-58
< REMOVAL AND INSTALLATION >
[AWD]
FRONT DRIVE SHAFT
4. Put alignment marks (A) on disc brake rotor and wheel hub and
bearing. Remove disc brake rotor.
CAUTION:
Do not drop the disc brake rotor.
5. Remove cotter pin.
6. Remove the nut retainer.
7. Loosen the wheel hub lock nut from the drive shaft using power tool.
8. Using a piece of wood and a suitable tool, tap on the lock nut to
disengage the drive shaft from the wheel hub and bearing.
CAUTION:
• Do not place the drive shaft joint at an extreme angle. Be
careful not to over extend the slide joint.
• Do not allow the drive shaft to hang without support.
NOTE:
Use a suitable puller if drive shaft cannot be separated from the
wheel hub and bearing.
9. Remove the wheel hub lock nut.
10. Remove the engine side cover. Refer to
EXT-28, "FENDER PROTECTOR : Exploded View"
.
11. Remove the lower nut and bolt from the steering knuckle. Refer to
.
12. Separate transverse link from steering knuckle. Refer to
.
13. Separate drive shaft from wheel hub and bearing. Reposition the drive shaft aside with wire. Refer to
14. Set Tool (A) and a suitable tool (B) between the drive shaft (slide
joint side) and the transaxle as shown. Remove the drive shaft.
CAUTION:
• Do not place drive shaft joint at an extreme angle when
removing drive shaft. Also be careful not to overextend
slide joint.
• Confirm that the circular clip is attached to the drive shaft.
15. Remove the differential side oil seal. Refer to
INSPECTION AFTER REMOVAL
• Move joint up/down, left/right, and in the axial directions. Check for motion that is not smooth and for signifi-
cant looseness.
JPDIG0066ZZ
JPDIG0070ZZ
Tool number (A)
: KV40107500 ( — )
JPDIF0004ZZ
FRONT DRIVE SHAFT
FAX-59
< REMOVAL AND INSTALLATION >
[AWD]
C
E
F
G
H
I
J
K
L
M
A
B
FAX
N
O
P
• Check boot for cracks, damage, and leakage of grease.
• Disassemble drive shaft and exchange malfunctioning part if there
is a non-standard condition.
INSTALLATION
Installation is in the reverse order of removal.
• Install a new differential side oil seal. Refer to
TM-210, "Removal and Installation"
.
CAUTION:
Do not reuse the differential side oil seal.
• Place Tool (A) onto transaxle assembly to prevent damage to the
differential side oil seal while inserting drive shaft. Slide drive shaft
sliding joint and tap with a suitable tool to install securely.
CAUTION:
Check that circular clip is completely engaged.
• Clean the mating surfaces of wheel hub lock nut and wheel hub and bearing.
CAUTION:
Do not apply lubricating oil to these mating surfaces.
• Clean the mating surfaces of drive shaft, wheel hub and bearing.
And then apply Molykote M77 lubricant to surface (A) of joint sub-
assembly of drive shaft.
CAUTION:
Apply paste to cover entire flat surface of joint sub-assembly
of drive shaft.
NOTE:
Always check with the Parts Department for the latest parts infor-
mation.
•
CAUTION:
• Since the drive shaft is assembled by press-fitting, use the tightening torque range for the wheel
hub lock nut.
• Be sure to use torque wrench to tighten the wheel hub lock nut. Do not use a power tool.
• Do not reuse wheel hub lock nut.
• Too much torque causes axle noise. Too little torque, causes wheel hub and bearing looseness.
Tighten the wheel hub lock nut to the specification.
SDIA1190J
Tool number (A)
: KV38107900 ( — )
JPDIF0023ZZ
JPDIG0122ZZ
FAX-60
< REMOVAL AND INSTALLATION >
[AWD]
FRONT DRIVE SHAFT
• Align the matching marks (A) made on the disc brake rotor and on
the front wheel hub and bearing during disassembly.
• When installing a cotter pin (1) and nut retainer (2), securely bend
the cotter pin to prevent rattles.
CAUTION:
Do not reuse cotter pin.
INSPECTION AFTER INSTALLATION
Check CVT fluid level and leakage. Refer to
Exploded View (RH)
INFOID:0000000011278656
JPDIG0066ZZ
JPDIF0295ZZ
AWDIA1213ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст