Nissan Rogue. Manual — part 690
FRONT DRIVE SHAFT BOOT
FAX-53
< REMOVAL AND INSTALLATION >
[AWD]
C
E
F
G
H
I
J
K
L
M
A
B
FAX
N
O
P
12. Separate drive shaft from wheel hub and bearing. Reposition the drive shaft aside with wire. Refer to
13. Remove boot bands.
14. Separate boot from joint sub-assembly.
15. Screw a suitable tool (A) 30 mm (1.18 in) or more into threaded
part of joint sub-assembly. Support drive shaft with one hand
and pull out joint sub-assembly with a sliding hammer or suitable
tool from housing assembly.
CAUTION:
• Align suitable tool and drive shaft and remove joint sub-
assembly by pulling directly.
• If joint sub-assembly cannot be removed after five or
more unsuccessful attempts, replace the entire drive shaft
assembly.
16. Remove circular clip (1) from shaft.
17. Remove outer boot from shaft.
INSPECTION AFTER REMOVAL
Check the following items, and replace the part if necessary.
• Move joint up/down, left/right, and in the axial directions. Check for
motion that is not smooth and for significant looseness.
• Check boot for cracks, damage, and leakage of grease.
INSTALLATION
1. Clean the old grease on joint sub-assembly with paper shop cloth.
2. Fill serration slot joint sub-assembly with Genuine NISSAN Grease.
CAUTION:
After applying grease, use a paper shop cloth to wipe off old grease that has oozed out.
NOTE:
Always check with the Parts Department for the latest parts information.
3. Install boot and boot bands to shaft.
CAUTION:
• Wrap serration on shaft with tape to protect the boot from damage.
• Do not reuse boot and boot band.
4. Remove the tape wrapped around the serration on shaft.
JPDIF0258ZZ
JPDIF0007ZZ
SDIA1190J
FAX-54
< REMOVAL AND INSTALLATION >
[AWD]
FRONT DRIVE SHAFT BOOT
5. Position the circular clip (1) on groove at the shaft edge.
CAUTION:
Do not reuse circular clip.
NOTE:
A drive joint inserter is recommended when installing the circular
clip.
6. Align the shaft and joint sub-assembly. Assemble the shaft with joint sub-assembly while holding the circu-
lar clip.
7. Install joint sub-assembly (1) to shaft using suitable tool.
CAUTION:
Confirm that joint sub-assembly is correctly engaged while
rotating drive shaft.
8. Apply the specified amount of Genuine NISSAN Grease into the large diameter side opening of the boot.
NOTE:
Always check with the Parts Department for the latest parts information.
9. Install the boot securely into grooves (indicated by “*” marks)
shown.
CAUTION:
If grease adheres to the boot mounting surface (indicated
by “*” mark) on the shaft or the joint sub-assembly, boot
may come off. Remove all grease from the boot mounting
surface.
10. Make sure boot installation length (L) is the specified length.
Insert a suitable tool into the large end of boot. Bleed air from
boot to prevent boot deformation.
CAUTION:
• Boot may break if boot installation length is not within standard value.
• Be careful that suitable tool does not contact inside surface of boot.
JPDIF0007ZZ
JPDIF0011ZZ
Grease quantity
: Refer to
.
Boot installation
length (L)
: Refer to
JPDIF0222ZZ
FRONT DRIVE SHAFT BOOT
FAX-55
< REMOVAL AND INSTALLATION >
[AWD]
C
E
F
G
H
I
J
K
L
M
A
B
FAX
N
O
P
11. Install new large and small boot bands securely using Tool.
CAUTION:
Do not reuse boot band.
12. Secure boot band so that dimension (M) meets the specification
as shown.
13. Attempt to rotate the boot to check whether or not the boot bands are securing the boot. If the boot is not
secure, remove the boot bands, reposition the boot, and install new boot bands.
14. Clean the mating surfaces of the joint sub-assembly (A) and the
wheel hub and bearing. Apply Molykote M77 lubricant to the sur-
face (A) of the joint sub-assembly.
CAUTION:
Apply lubricant to cover the entire flat mating surface of the
joint sub-assembly.
NOTE:
Always check with the Parts Department for the latest parts
information.
15. Clean the mating surfaces of the wheel hub lock nut and wheel hub and bearing.
CAUTION:
Do not apply lubricating oil to these mating surfaces.
16. Insert drive shaft to wheel hub and bearing.
17. Temporarily install the wheel hub lock nut.
CAUTION:
Do not reuse the wheel hub lock nut.
18. Install the transverse link to the steering knuckle. Tighten the steering knuckle nut and bolt to the specifi-
cation. Refer to
.
19. Align the marks (A) made on the disc brake rotor and on the
wheel hub and bearing during disassembly.
Tool number : KV40107300 ( — )
RAC1133D
Dimension (M)
.
DSF0047D
JPDIG0122ZZ
JPDIG0066ZZ
FAX-56
< REMOVAL AND INSTALLATION >
[AWD]
FRONT DRIVE SHAFT BOOT
20. Install brake caliper to steering knuckle. Refer to
BR-37, "BRAKE CALIPER ASSEMBLY (1 PISTON
(1 PISTON TYPE), or
BR-42, "BRAKE CALIPER ASSEMBLY (2 PISTON TYPE)
21. Install the front wheel sensor to the steering knuckle. Refer to
BRC-130, "FRONT WHEEL SENSOR :
.
CAUTION:
• Before installing, make sure there is no foreign material such as iron fragments adhered to the
pick-up part of the front wheel sensor.
• When installing, make sure there is no foreign material such as iron fragments on and in the hole
in the steering knuckle for the front wheel sensor. Make sure no foreign material has been
caught in the sensor rotor. Remove any foreign material and then install the front wheel sensor.
22. Hold the wheel hub and bearing. tighten the wheel hub lock nut. Refer to
CAUTION:
• Since the drive shaft is assembled by press-fitting, use a torque wrench to tighten the wheel hub
lock nut. Do not use a power tool.
• Too much torque causes axle noise. too little torque causes wheel bearing looseness. Tighten
the wheel hub lock nut to the specification.
23. Install the nut retainer (2) and a new cotter pin (1), securely
bend the cotter pin to prevent rattles.
CAUTION:
• Do not reuse cotter pin.
• Bend cotter pin securely to prevent any looseness.
24. Install the front wheel and tire. Refer to
WT-67, "Removal and Installation"
INSPECTION AFTER INSTALLATION
Check the wheel sensor harness to be sure the connectors are fully seated.
TRANSAXLE SIDE
TRANSAXLE SIDE : Removal and Installation
INFOID:0000000011278652
NOTE:
Remove boot after removing drive shaft.
• For drive shaft removal and installation, refer to
FAX-57, "Removal and Installation (LH)"
"Removal and Installation (RH)"
(RH).
• For drive shaft disassembly and assembly, refer to
FAX-65, "Disassembly and Assembly (LH)"
(LH) or
70, "Disassembly and Assembly (RH)"
JPDIF0295ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст