Nissan Rogue. Manual — part 94
AV-368
< SYMPTOM DIAGNOSIS >
[NAVIGATION WITH BOSE]
NORMAL OPERATING CONDITION
- Because calculation of the current location cannot be done when traveling with the ignition off, for example
when traveling by ferry or when being towed, the location before travel is displayed. If the precise location
can be detected with GPS, the location will be corrected.
Vehicle Mark Jumps
In the following cases, the vehicle mark may appear to jump as a result of automatic correction of the current
location:
• When map matching has been done
- If the current location and the vehicle mark are different when map matching is done, the vehicle mark may
seem to jump. At this time, the location may be “corrected” to the wrong road or to a location which is not on
a road.
• When GPS location correction has been done
- If the current location and the vehicle mark are different when the location is corrected using GPS measure-
ments, the vehicle mark may seem to jump. At this time, the location may be “corrected” to a location which
is not on a road.
Vehicle Mark is in a River or Sea
The navigation system moves the vehicle mark with no distinction between land and rivers or sea. If the vehi-
cle mark is somehow out of place, it may appear that the vehicle is driving in a river or the sea.
Vehicle Mark Automatically Rotates
The system wrongly memorizes the rotating status as stopping when the ignition switch is turned ON with the
turntable rotating. That causes the vehicle mark to rotate when the vehicle is stopped.
When Driving on Same Road, Sometimes Vehicle Mark is in Right Place and Sometimes it is in Wrong Place
The conditions of the GPS antenna (GPS data) and gyroscope (angular speed sensor) change gradually.
Depending on the road traveled and the operation of the steering wheel, the location detection results will be
different. Therefore, even on a road on which the location has never been wrong, conditions may cause the
vehicle mark to deviate.
AV
AV CONTROL UNIT
AV-369
< REMOVAL AND INSTALLATION >
[NAVIGATION WITH BOSE]
C
D
E
F
G
H
I
J
K
L
M
B
A
O
P
REMOVAL AND INSTALLATION
AV CONTROL UNIT
Exploded View
INFOID:0000000011277018
Removal and Installation
INFOID:0000000011277019
REMOVAL
CAUTION:
• Before disconnecting the AV control unit and battery terminals, turn the ignition switch OFF and wait
at least 30 seconds.
• Before replacing AV control unit, perform “READ CONFIGURATION” to save current vehicle specifi-
cation. Refer to
AV-132, "CONFIGURATION (AV CONTROL UNIT) : Configuration List"
.
NOTE:
After the ignition switch is turned OFF, the AV control unit continues operating for approximately 30 seconds.
Therefore, data corruption may occur if battery voltage is cut off within 30 seconds.
1. Disconnect the negative battery terminal. Refer to
PG-78, "Removal and Installation (Battery)"
2. Remove cluster lid C. Refer to
IP-22, "Removal and Installation"
3. Remove instrument finisher B. Refer to
IP-16, "INSTRUMENT FINISHER B : Removal and Installation"
.
4. Remove instrument finisher E. Refer to
IP-16, "INSTRUMENT FINISHER E : Removal and Installation"
.
5. Remove the AV control unit screws, then pull out the AV control unit.
6. Disconnect the harness connectors from the AV control unit and remove.
7. Remove the AV control unit bracket (LH/RH) screws and the AV control unit brackets (LH/RH) (if neces-
sary).
INSTALLATION
Installation is in the reverse order of removal.
CAUTION:
1.
AV control unit bracket (LH)
2.
AV control unit
3.
AV control unit bracket (RH)
AWNIA3339ZZ
AV-370
< REMOVAL AND INSTALLATION >
[NAVIGATION WITH BOSE]
AV CONTROL UNIT
• When replacing AV control unit, perform "WRITE CONFIGURATION". Refer to
TION (AV CONTROL UNIT) : Configuration List"
• When replacing AV control unit, the AV control unit must be registered. Refer to
AV
STEERING SWITCH
AV-371
< REMOVAL AND INSTALLATION >
[NAVIGATION WITH BOSE]
C
D
E
F
G
H
I
J
K
L
M
B
A
O
P
STEERING SWITCH
Exploded View
INFOID:0000000011277020
Removal and Installation
INFOID:0000000011277021
REMOVAL
NOTE:
The steering switches are serviced as an assembly.
1. Remove steering wheel. Refer to
ST-11, "Removal and Installation"
.
2. Release pawls on the steering wheel rear finisher and remove.
3. Remove screws (A) and release pawls (B) and remove steering
switches (1) from steering wheel (2).
:
Pawls
INSTALLATION
Installation is in the reverse order of removal.
1.
Steering wheel rear finisher
2.
Steering wheel
3.
Steering switches
Pawl
AWNIA3722ZZ
AWNIA3723ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст