Nissan Rogue. Manual — part 937
PARKING BRAKE FRONT CABLE
PB-9
< REMOVAL AND INSTALLATION >
C
D
E
G
H
I
J
K
L
M
A
B
PB
N
O
P
PARKING BRAKE FRONT CABLE
Removal and Installation
INFOID:0000000011280107
REMOVAL
1. Disconnect the positive and negative battery terminals. Refer to
2. Remove the parking brake control. Refer to
PB-8, "Removal and Installation"
3. Remove driver seat (LH). Refer to
SE-32, "DRIVER SIDE : Removal and Installation"
.
4. Remove the center console. Refer to
IP-19, "Removal and Installation"
.
5. Remove front door welts (LH). Refer to
INT-23, "BODY SIDE WELT : Removal and Installation - Front
.
6. Remove dash side finisher (LH). Refer to
INT-24, "DASH SIDE FINISHER : Removal and Installation"
7. Remove shift selector knob. Refer to
8. Remove the front floor connecting ducts (LH/RH). Refer to
VTL-10, "FRONT FLOOR DUCT : Removal
and Installation - Front Floor Connecting Duct"
.
9. Remove the front floor duct. Refer to
VTL-11, "FRONT FLOOR DUCT : Removal and Installation - Front
10. Remove the rear center ventilator duct. Refer to
VTL-11, "REAR CENTER VENTILATOR DUCT :
.
11. Release clips (A) using a suitable tool and remove steering joint
floor cover (1).
12. Place front floor trim aside and remove the front floor spacer. Refer to
.
13. Remove the bolts from the parking brake front cable mount. Refer to
.
14. Pull equalizer (A) of the parking brake front cable (1) in a rear-
ward direction and then push upward to separate each parking
brake rear cable (2) from the parking brake front cable (1).
CAUTION:
To prevent damage to the parts, do not bend the parking
brake cables.
15. Remove the parking brake front cable.
INSTALLATION
Installation is in the reverse order of removal.
CAUTION:
Do not reuse the adjusting nut.
• Inspect and adjust the parking brake pedal. Refer to
PB-4, "Inspection and Adjustment"
.
• If a malfunction is indicated by the air bag warning lamp after repair or replacement of the malfunctioning
parts, perform the SRS Final Check. Refer to
SRC-16, "Trouble Diagnosis with CONSULT"
.
ALJIA1359ZZ
JPFIB0129ZZ
PB-10
< REMOVAL AND INSTALLATION >
PARKING BRAKE REAR CABLE
PARKING BRAKE REAR CABLE
Removal and Installation
INFOID:0000000011280108
REMOVAL
1. Remove the center console assembly. Refer to
IP-19, "Removal and Installation"
2. Remove shift selector. Refer to
TM-193, "Removal and Installation"
.
3. Remove the bolts from the parking brake front cable mount. Refer to
.
4. Loosen the adjusting nut. Refer to
.
NOTE:
It is not necessary to remove the parking brake front cable.
5. Pull equalizer (A) of the parking brake front cable (1) in a rearward direction and then push upward to sep-
arate each parking brake rear cable (2) from the parking brake front cable (1).
CAUTION:
To prevent damage to the parts, do not bend the parking
brake cables.
6. Press the pawl (1) to remove each parking brake rear cable from
the vehicle.
7. Separate the parking brake rear cable from the toggle lever. Refer to
.
INSTALLATION
Installation is in the reverse order of removal.
CAUTION:
Do not reuse the adjusting nut if the nut is removed.
• Inspect and adjust the parking brake shoes. Refer to
PB-6, "Inspection and Adjustment"
JPFIB0129ZZ
JPFIB0130ZZ
PARKING BRAKE SWITCH
PB-11
< REMOVAL AND INSTALLATION >
C
D
E
G
H
I
J
K
L
M
A
B
PB
N
O
P
PARKING BRAKE SWITCH
Removal and Installation
INFOID:0000000011280109
REMOVAL
1. Remove the instrument lower panel LH. Refer to
IP-23, "Removal and Installation"
.
2. Disconnect the harness connector from the parking brake switch. Refer to
3. Remove the screw and remove the parking brake switch. Refer to
INSTALLATION
Installation is in the reverse order of removal.
CAUTION:
Replace the parking brake switch if it has been dropped or sustained an impact.
Adjust the parking brake cable if necessary. Refer to
PB-12
< REMOVAL AND INSTALLATION >
PARKING BRAKE SHOE
PARKING BRAKE SHOE
Exploded View
INFOID:0000000011280110
Removal and Installation
INFOID:0000000011280111
REMOVAL
WARNING:
Clean dust on the parking brake shoes with a vacuum dust collector to minimize the hazard of air-
borne particles or other materials.
1. Remove the rear wheel and tire using power tool. Refer to
WT-67, "Removal and Installation"
.
2. Remove the brake caliper torque member bolts, leaving the brake hose attached. Position the caliper
aside with wire. Refer to
BR-47, "BRAKE CALIPER ASSEMBLY : Removal and Installation"
CAUTION:
Do not depress the brake pedal while the caliper assembly is removed.
3. Put alignment marks on the disc brake rotor and on the wheel hub and bearing and remove the disc brake
rotor.
CAUTION:
Do not drop the disc brake rotor.
4. If disc brake rotor cannot be removed, remove as follows:
a. Secure the disc brake rotor with wheel nuts and remove the adjusting hole plug.
1.
Back plate
2.
Parking brake shoe
3.
Brake strut
4.
Return spring
5.
Spring
6.
Return spring to brake strut
7.
Adjuster
8.
Toggle lever
9.
Anti-rattle pin
: Apply PBC (Poly Butyl Cuprysil) grease or silicone-based grease.
AWFIA1077ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст