Nissan Rogue. Manual — part 229
DAS
CONFIGURATION (AROUND VIEW MONITOR CONTROL UNIT)
DAS-87
< BASIC INSPECTION >
[DRIVER ASSISTANCE SYSTEM]
C
D
E
F
G
H
I
J
K
L
M
B
N
P
A
Confirm that each function controlled by around view monitor control unit operates normally.
>> Work End.
Configuration List
INFOID:0000000011444773
CAUTION:
Thoroughly read and understand the vehicle specification. Incorrect settings may result in abnormal
control of ECU.
⇔: Items which confirm vehicle specifications
MANUAL SETTING ITEM
Items
Setting value
BCI FUNCTION
WITH
⇔ WITHOUT
DAS-88
< BASIC INSPECTION >
[DRIVER ASSISTANCE SYSTEM]
PREDICTIVE COURSE LINE CENTER POSITION ADJUSTMENT
PREDICTIVE COURSE LINE CENTER POSITION ADJUSTMENT
Description
INFOID:0000000011444774
Adjust the center position of the predictive course line of the rear view monitor if it is shifted.
Work Procedure
INFOID:0000000011444775
1.
DRIVING
Drive the vehicle straight ahead 100 m (328.1 ft) or more at a speed of 30 km/h (18.6 MPH) or more.
>> End.
DAS
CALIBRATING CAMERA IMAGE (AROUND VIEW MONITOR)
DAS-89
< BASIC INSPECTION >
[DRIVER ASSISTANCE SYSTEM]
C
D
E
F
G
H
I
J
K
L
M
B
N
P
A
CALIBRATING CAMERA IMAGE (AROUND VIEW MONITOR)
Description
INFOID:0000000011444776
• Calibration must be performed after removing/replacing the cameras, removing parts (e.g. front grille, door
mirror, and others) mounted on the cameras, or replacing the Around view monitor control unit.
• The use of CONSULT is required to perform calibration or writing of calibration results to the Around view
monitor control unit.
• Align the white lines on the road near the vehicle at the boundary of each camera image by this camera cal-
ibration. The white lines far from the vehicle may not be aligned at the boundary of each camera image. The
farther the line, the greater the difference is.
Work Procedure
INFOID:0000000011444777
CALIBRATION FLOWCHART
Following the flowchart shown in the figure, perform the calibration.
NOTE:
View in the incomplete calibration state is indicated by “
” on the
around view monitor.
CALIBRATION PROCEDURE
1.
AROUND VIEW MONITOR SCREEN CONFIRMATION
JSNIA4210GB
AWNIA2590GB
DAS-90
< BASIC INSPECTION >
[DRIVER ASSISTANCE SYSTEM]
CALIBRATING CAMERA IMAGE (AROUND VIEW MONITOR)
Check that there is no indication of “Incomplete calibration”.
Is the “Incomplete calibration” display visible?
YES
>> GO TO 2.
NO
>> GO TO 4.
2.
CHECK THAT AROUND VIEW MONITOR CONTROL UNIT IS REPLACED
Check that the around view monitor control unit is replaced.
Is the around view monitor control unit replaced?
YES
>> GO TO 3.
NO
>> GO TO 5.
3.
CANCEL THE INDICATION OF INCOMPLETE CALIBRATION (PERFORM THIS ONLY AFTER REPLAC-
ING AROUND VIEW MONITOR CONTROL UNIT.)
CONSULT work support
1. On the CONSULT screen, touch “CALIBRATING CAMERA IMAGE (FRONT CAMERA)”, “CALIBRATING
CAMERA IMAGE (PASS-SIDE CAMERA)”, “CALIBRATING CAMERA IMAGE (DR-SIDE CAMERA)”, or
“CALIBRATING CAMERA IMAGE (REAR CAMERA)” to accept the selection.
NOTE:
To cancel the indication of Incomplete calibration, select items based on the target camera.
2. On the adjustment screen of each camera, touch “APPLY” but-
ton. After this, touch “OK” button.
CAUTION:
• Never perform operations other than those mentioned
above.
• Never perform “Initialize Camera Image Calibration”.
3. Display the around view monitor screen to check that there is no
errors, such as deviations among the camera images.
Is there a malfunction?
YES
>> Calibration End.
NO
>> GO TO 1.
4.
PERFORM SIMPLIFIED CONFIRMATION/ADJUSTMENT BY “FINE TUNING OF BIRDS-EYE VIEW”
1. Put target line 1 on the ground beside each axle using packing tape, etc.
2. Put target lines 2 equal to the vehicle total length + approximately 1.0 m (39.3 in) from the vehicle side
(right and left) at approximately 30 cm (11.8 in) away from the vehicle (make the line as parallel with the
vehicle as possible).
AWNIA2590GB
JSNIA4212ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст