Nissan Rogue. Manual — part 429
DMS-18
< REMOVAL AND INSTALLATION >
[SPORT MODE]
SPORT MODE SWITCH
REMOVAL AND INSTALLATION
SPORT MODE SWITCH
Removal and Installation
INFOID:0000000011279923
REMOVAL
1. Remove instrument lower panel LH. Refer to
IP-23, "Removal and Installation"
.
2. Release pawls using suitable tool and remove SPORT mode
switch (1) from instrument lower panel LH.
: Pawl
INSTALLATION
Installation is in the reverse order of removal.
AWDIA1211ZZ
DMS
PRECAUTIONS
DMS-19
< PRECAUTION >
[ECO MODE]
C
D
E
F
G
H
I
J
K
L
M
B
N
P
A
PRECAUTION
PRECAUTIONS
Precaution for Supplemental Restraint System (SRS) "AIR BAG" and "SEAT BELT
PRE-TENSIONER"
INFOID:0000000011317484
The Supplemental Restraint System such as “AIR BAG” and “SEAT BELT PRE-TENSIONER”, used along
with a front seat belt, helps to reduce the risk or severity of injury to the driver and front passenger for certain
types of collision. Information necessary to service the system safely is included in the SR and SB section of
this Service Manual.
WARNING:
• To avoid rendering the SRS inoperative, which could increase the risk of personal injury or death in
the event of a collision which would result in air bag inflation, all maintenance must be performed by
an authorized NISSAN/INFINITI dealer.
• Improper maintenance, including incorrect removal and installation of the SRS, can lead to personal
injury caused by unintentional activation of the system. For removal of Spiral Cable and Air Bag
Module, see the SR section.
• Do not use electrical test equipment on any circuit related to the SRS unless instructed to in this
Service Manual. SRS wiring harnesses can be identified by yellow and/or orange harnesses or har-
ness connectors.
PRECAUTIONS WHEN USING POWER TOOLS (AIR OR ELECTRIC) AND HAMMERS
WARNING:
• When working near the Airbag Diagnosis Sensor Unit or other Airbag System sensors with the Igni-
tion ON or engine running, DO NOT use air or electric power tools or strike near the sensor(s) with a
hammer. Heavy vibration could activate the sensor(s) and deploy the air bag(s), possibly causing
serious injury.
• When using air or electric power tools or hammers, always switch the Ignition OFF, disconnect the
battery and wait at least three minutes before performing any service.
Precaution for Work
INFOID:0000000011376590
• When removing or disassembling each component, be careful not to damage or deform it. If a component
may be subject to interference, be sure to protect it with a shop cloth.
• When removing (disengaging) components with a screwdriver or similar tool, be sure to wrap the component
with a shop cloth or vinyl tape to protect it.
• Protect the removed parts with a shop cloth and prevent them from being dropped.
• Replace a deformed or damaged clip.
• If a part is specified as a non-reusable part, always replace it with a new one.
• Be sure to tighten bolts and nuts securely to the specified torque.
• After installation is complete, be sure to check that each part works properly.
• Follow the steps below to clean components:
- Water soluble dirt:
• Dip a soft cloth into lukewarm water, wring the water out of the cloth and wipe the dirty area.
• Then rub with a soft, dry cloth.
- Oily dirt:
• Dip a soft cloth into lukewarm water with mild detergent (concentration: within 2 to 3%) and wipe the dirty
area.
• Then dip a cloth into fresh water, wring the water out of the cloth and wipe the detergent off.
• Then rub with a soft, dry cloth.
- Do not use organic solvent such as thinner, benzene, alcohol or gasoline.
- For genuine leather seats, use a genuine leather seat cleaner.
DMS-20
< PREPARATION >
[ECO MODE]
PREPARATION
PREPARATION
PREPARATION
Special Service Tool
INFOID:0000000011376591
The actual shape of the tools may differ from those illustrated here.
Tool number
(TechMate No.)
Tool name
Description
—
(J-46534)
Trim Tool Set
Removing trim components
AWJIA0483ZZ
DMS
COMPONENT PARTS
DMS-21
< SYSTEM DESCRIPTION >
[ECO MODE]
C
D
E
F
G
H
I
J
K
L
M
B
N
P
A
SYSTEM DESCRIPTION
COMPONENT PARTS
Component Parts Location
INFOID:0000000011317485
COMPONENT DESCRIPTION
Instrument lower panel LH
ALOIA0241ZZ
No.
Component
Function
Combination meter
• The combination meter transmittes the following signal via CAN communications
to the TCM.
- ECO mode switch signal
• The combination meter receives the following signal via CAN communications
from the ECM.
- ECO mode indicator signal
Refer to
MWI-6, "METER SYSTEM : Component Parts Location"
for detailed instal-
lation location.
TCM
• The TCM receives the following signal via CAN communications from the combi-
nation meter.
- ECO mode switch signal
• The TCM transmittes the following signal via CAN communications to the ECM.
- ECO mode signal
Refer to
TM-12, "CVT CONTROL SYSTEM : Component Parts Location"
for detailed
installation location.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст