Nissan Qashqai J11. Manual — part 2178
DAS-126
< DTC/CIRCUIT DIAGNOSIS >
[DRIVER ASSISTANCE SYSTEM]
U1000 CAN COMM CIRCUIT
U1000 CAN COMM CIRCUIT
AROUND VIEW MONITOR CONTROL UNIT
AROUND VIEW MONITOR CONTROL UNIT : DTC Logic
INFOID:0000000010416862
DTC DETECTION LOGIC
AROUND VIEW MONITOR CONTROL UNIT : Diagnosis Procedure
INFOID:0000000010416863
1.
PERFORM SELF DIAGNOSTIC RESULT
1.
Turn ignition switch ON and wait for 2 seconds or more.
2.
Perform “Self Diagnostic Result” for “AVM”.
Is DTC detected?
YES
>> Refer to
LAN-24, "Trouble Diagnosis Flow Chart"
NO
>> Refer to
GI-41, "Intermittent Incident"
.
DISTANCE SENSOR
DISTANCE SENSOR : DTC Logic
INFOID:0000000010416864
DTC DETECTION LOGIC
DISTANCE SENSOR : Diagnosis Procedure
INFOID:0000000010416865
1.
PERFORM SELF DIAGNOSTIC RESULT
1.
Turn ignition switch ON and wait for 2 seconds or more.
2.
Perform “Self Diagnostic Result” for “LASER/RADAR”
Is DTC detected?
YES
>> Refer to
LAN-24, "Trouble Diagnosis Flow Chart"
NO
>> Refer to
GI-41, "Intermittent Incident"
.
FRONT CAMERA UNIT
FRONT CAMERA UNIT : DTC Logic
INFOID:0000000010632314
DTC DETECTION LOGIC
FRONT CAMERA UNIT : Diagnosis Procedure
INFOID:0000000010632315
CONSULT Display
DTC Detection Condition
Possible Cause
CAN COMM CIRCUIT
[U1000]
Around view monitor control unit is not transmit-
ting or receiving CAN communication signal for 2
seconds or more.
CAN communication system.
CONSULT Display
DTC Detection Condition
Possible Cause
CAN COMM CIRCUIT
[U1000]
Distance sensor is not transmitting or receiving
CAN communication signal for 2 seconds or
more.
CAN communication system.
CONSULT Display
DTC Detection Condition
Possible Cause
CAN COMM CIRCUIT
[U1000]
Front camera unit is not transmitting or receiving
CAN communication signal for 2 seconds or
more.
CAN communication system.
DAS
U1000 CAN COMM CIRCUIT
DAS-127
< DTC/CIRCUIT DIAGNOSIS >
[DRIVER ASSISTANCE SYSTEM]
C
D
E
F
G
H
I
J
K
L
M
B
N
P
A
1.
PERFORM SELF DIAGNOSTIC RESULT
1.
Turn ignition switch ON and wait for 2 seconds or more.
2.
Perform “Self Diagnostic Result” for “LANE CAMERA”
Is DTC detected?
YES
>> Refer to
LAN-24, "Trouble Diagnosis Flow Chart"
NO
>> Refer to
GI-41, "Intermittent Incident"
.
DAS-128
< DTC/CIRCUIT DIAGNOSIS >
[DRIVER ASSISTANCE SYSTEM]
U1010 CONTROL UNIT (CAN)
U1010 CONTROL UNIT (CAN)
AROUND VIEW MONITOR CONTROL UNIT
AROUND VIEW MONITOR CONTROL UNIT : DTC Logic
INFOID:0000000010416866
DTC DETECTION LOGIC
DISTANCE SENSOR
DISTANCE SENSOR : DTC Logic
INFOID:0000000010416867
DTC DETECTION LOGIC
FRONT CAMERA UNIT
FRONT CAMERA UNIT : DTC Logic
INFOID:0000000010632316
DTC DETECTION LOGIC
CONSULT Display
DTC Detection Condition
Possible Cause
CONTROL UNIT (CAN)
[U1010]
Error during CAN controller hardware initializa-
tion (VCAN).
Replace the Around view monitor control unit if
the malfunction occurs constantly.
Refer to
AV-267, "Removal and Installation"
.
CONSULT Display
DTC Detection Condition
Possible Cause
CONTROL UNIT (CAN)
[U1010]
Error during CAN controller hardware initializa-
tion (VCAN).
Replace the distance sensor if the malfunction
occurs constantly.
Refer to
DAS-203, "Removal and Installation"
.
CONSULT Display
DTC Detection Condition
Possible Cause
CONTROL UNIT (CAN)
[U1010]
Error during CAN controller hardware initializa-
tion (VCAN).
Replace the front camera unit if the malfunction
occurs constantly.
Refer to
DAS-201, "Removal and Installation"
.
DAS
U111A REAR CAMERA IMAGE SIGNAL CIRCUIT
DAS-129
< DTC/CIRCUIT DIAGNOSIS >
[DRIVER ASSISTANCE SYSTEM]
C
D
E
F
G
H
I
J
K
L
M
B
N
P
A
U111A REAR CAMERA IMAGE SIGNAL CIRCUIT
DTC Logic
INFOID:0000000010416868
DTC DETECTION LOGIC
Diagnosis Procedure
INFOID:0000000010416869
WITH PUMP CONTROL UNIT
1.
CHECK REAR CAMERA POWER SUPPLY AND GROUND CIRCUIT CONTINUITY
1.
Turn ignition switch OFF.
2.
Disconnect around view monitor control unit and rear camera connectors.
3.
Check continuity between around view monitor control unit connector and rear camera connector.
4.
Check continuity between around view monitor control unit connector and ground.
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> Repair or replace harness or connectors.
2.
CHECK REAR CAMERA POWER SUPPLY VOLTAGE
1.
Connect around view monitor control unit and rear camera connectors.
2.
Turn ignition switch ON.
3.
Check voltage between around view monitor control unit connector and ground.
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> Replace around view monitor control unit. Refer to
AV-267, "Removal and Installation"
3.
CHECK REAR CAMERA IMAGE SIGNAL AND IMAGE SIGNAL GROUND CIRCUIT CONTINUITY
1.
Turn ignition switch OFF.
2.
Disconnect around view monitor control unit and rear camera connectors.
3.
Check continuity between around view monitor control unit connector and rear camera connector.
CONSULT Display
DTC Detection Condition
Possible Cause
REAR CAMERA IMAGE SIG-
NAL
[U111A]
Rear camera image signal circuit open or short.
Check rear camera image signal circuit.
Around view monitor control unit
Rear camera
Continuity
Connector
Terminals
Connector
Terminals
M8
50
D80
8
Existed
52
7
Around view monitor control unit
Ground
Continuity
Connector
Terminal
M8
50
Not existed
Around view monitor control unit
Ground
Condition
Voltage
(Approx.)
Connector
Terminal
M8
50
—
CAMERA switch is ON or
selector lever in R (re-
verse).
6.0 V
Around view monitor control unit
Rear camera
Continuity
Connector
Terminals
Connector
Terminals
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст