Nissan Qashqai J11. Manual — part 850
REAR DRIVE SHAFT
RAX-11
< PERIODIC MAINTENANCE >
[4WD]
C
E
F
G
H
I
J
K
L
M
A
B
RAX
N
O
P
REAR DRIVE SHAFT
Inspection
INFOID:0000000010297908
• Check drive shaft mounting point and joint for looseness and other damage.
• Check boot for cracks and other damage.
CAUTION:
Replace entire drive shaft assembly when noise or vibration occur from drive shaft.
RAX-12
< REMOVAL AND INSTALLATION >
[4WD]
REAR WHEEL HUB AND HOUSING
REMOVAL AND INSTALLATION
REAR WHEEL HUB AND HOUSING
Exploded View
INFOID:0000000010297909
Removal and Installation
INFOID:0000000010297910
REMOVAL
Wheel Hub and Bearing Assembly
1.
Remove tires from vehicle.
2.
Remove torque member mounting bolts. Hang torque member not to interfere with work. Refer to
"BRAKE CALIPER ASSEMBLY : Exploded View"
(LHD),
BR-86, "BRAKE CALIPER ASSEMBLY :
(RHD).
CAUTION:
Never depress brake pedal while brake caliper is removed.
3.
Remove disc rotor.
4.
Remove cotter pin, and then loosen hub lock nut.
5.
Patch hub lock nut with a piece of wood. Hammer the wood to
disengage wheel hub and bearing assembly from drive shaft.
Remove the hub lock nut.
CAUTION:
• Never place drive shaft joint at an extreme angle. Also be
careful not to overextend slide joint.
• Never drop drive shaft. Support drive shaft by housing,
joint sub-assembly, shaft etc.
NOTE:
Use suitable puller, if wheel hub and bearing assembly and drive
shaft cannot be separated even after performing the above pro-
cedure.
6.
Remove wheel hub and bearing assembly.
INSTALLTION
Install in the reverse order of removal.
1.
Axle housing
2.
Suspension arm
3.
Back plate
4.
Wheel hub and bearing assembly
5.
Cotter pin
Refer to
for symbols in the figure.
E1DIA0226GB
JPDIF0003ZZ
REAR WHEEL HUB AND HOUSING
RAX-13
< REMOVAL AND INSTALLATION >
[4WD]
C
E
F
G
H
I
J
K
L
M
A
B
RAX
N
O
P
Inspection
INFOID:0000000010297911
INSPECTION AFTER REMOVAL
Check wheel hub and bearing assembly for wear, cracks, and damage. Replace if there are.
INSPECTION AFTER INSTALLATION
Check wheel alignment. Refer to
FSU-7, "Wheel Alignment Inspection"
.
RAX-14
< REMOVAL AND INSTALLATION >
[4WD]
REAR DRIVE SHAFT
REAR DRIVE SHAFT
Exploded View
INFOID:0000000010297912
REMOVAL
DISASSEMBLY
Removal and Installation
INFOID:0000000010297913
REMOVAL
1.
Remove tires from vehicle.
2.
Remove torque member mounting bolts. Hang torque member not to interfere with work. Refer to
"BRAKE CALIPER ASSEMBLY : Exploded View"
(LHD),
BR-86, "BRAKE CALIPER ASSEMBLY :
(RHD).
CAUTION:
Never depress brake pedal while brake caliper is removed.
1.
Drive shaft
2.
Cotter pin
Refer to
for symbols in the figure.
PDIA1172J
1.
Circular clip
2.
Dust shield
3.
Housing
4.
Snap ring
5.
Spider assembly
6.
Boot band
7.
Boot
8.
Shaft
9.
Circular clip
10. Joint sub-assembly
11.
Sensor rotor
: Wheel side
: Fill NISSAN genuine grease or an equivalent.
Refer to
for symbols not described on the above.
JPDIG0015ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст