Nissan Qashqai J11. Manual — part 848
REAR WHEEL HUB AND HOUSING
RAX-3
< PERIODIC MAINTENANCE >
[2WD]
C
E
F
G
H
I
J
K
L
M
A
B
RAX
N
O
P
PERIODIC MAINTENANCE
REAR WHEEL HUB AND HOUSING
Exploded View
INFOID:0000000010297897
.
Inspection
INFOID:0000000010297898
MOUNTING INSPECTION
Make sure the mounting conditions (looseness, back lash) of each component and component conditions
(wear, damage) are normal.
WHEEL BEARING INSPECTION
• Move wheel hub and bearing assembly in the axial direction by hand. Make sure there is no looseness of
wheel bearing.
• Rotate wheel hub, and make sure there is no unusual noise or other irregular conditions. If there is any of
irregular conditions, replace wheel hub and bearing assembly.
Standard
Axial end play
: Refer to
.
RAX-4
< REMOVAL AND INSTALLATION >
[2WD]
REAR WHEEL HUB
REMOVAL AND INSTALLATION
REAR WHEEL HUB
Exploded View
INFOID:0000000010297899
Removal and Installation
INFOID:0000000010481080
REMOVAL
Wheel Hub and Bearing
1.
Remove the wheel and tire using power tool. Refer to
WT-60, "Wheel Balance Adjustment (Aluminum
.
2.
Remove the bolt and separate the rear wheel sensor from the wheel hub and bearing. Refer to
"REAR WHEEL SENSOR : Removal and Installation"
.
CAUTION:
• Failure to separate the rear wheel sensor from the wheel hub and bearing may result in damage
to the rear wheel sensor.
• Pull out the rear wheel sensor, being careful to turn it as little as possible. Never pull on wheel
sensor harness.
3.
Remove torque member bolts using power tool, leaving the brake hose attached. Position brake caliper
aside with wire. Refer to
BR-43, "BRAKE CALIPER ASSEMBLY : Exploded View"
CAUTION:
Never depress brake pedal while brake caliper is removed.
4.
Put alignment marks on the disc brake rotor and on the wheel hub and bearing. Remove the disc brake
rotor. Remove disc brake rotor.
CAUTION:
Never drop disc brake rotor.
5.
Remove the hub bolts and the wheel hub and bearing.
1.
Suspension arm
2.
Back plate
3.
Wheel hub and bearing assembly
Refer to
for symbols in the figure.
E1DIA0225GB
REAR WHEEL HUB
RAX-5
< REMOVAL AND INSTALLATION >
[2WD]
C
E
F
G
H
I
J
K
L
M
A
B
RAX
N
O
P
6.
If necessary, remove the wheel studs (1) from the wheel hub
and bearing using a suitable tool (A).
CAUTION:
• Remove the wheel studs only when necessary.
• Never hammer the wheel studs or damage to the wheel
hub and bearing may occur.
• Pull out the wheel studs in a direction perpendicular to
the wheel hub and bearing.
INSTALLATION
Installation is in the reverse order of removal.
• Place a washer (A) as shown to install the wheel studs (1) by using
the tightening force of the nut (B).
CAUTION:
• Never reuse the wheel stud.
• Check that there is no clearance between the wheel stud
and the wheel hub and bearing.
• Before installing, make sure there is no foreign material
such as iron fragments adhered to the pick-up part of the
rear wheel sensor.
• When installing, make sure there is no foreign material such
as iron fragments on and in the hole in the wheel hub and
bearing for the rear wheel sensor. Make sure no foreign
material has been caught in the sensor rotor. Remove any foreign material and clean the mount.
• Install the rear wheel sensor to the wheel hub and bearing. Refer to
.
• Align the matching marks made during removal when reusing the disc brake rotor.
• Check that the wheel hub and bearing operates smoothly.
• Perform the inspection after installation. Refer to
Inspection
INFOID:0000000010297901
INSPECTION AFTER REMOVAL
Check wheel hub and bearing assembly for wear, cracks, and damage. Replace if there are.
INSPECTION AFTER INSTALLATION
Check wheel alignment. Refer to
FSU-7, "Wheel Alignment Inspection"
.
JPDIF0299ZZ
JPDIF0300ZZ
RAX-6
< SERVICE DATA AND SPECIFICATIONS (SDS)
[2WD]
SERVICE DATA AND SPECIFICATIONS (SDS)
SERVICE DATA AND SPECIFICATIONS (SDS)
SERVICE DATA AND SPECIFICATIONS (SDS)
Wheel Bearing
INFOID:0000000010297902
Axial end play
0.05 mm (0.002 in) or less
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст