Nissan Qashqai J11. Manual — part 1748
EXL-294
< DTC/CIRCUIT DIAGNOSIS >
[HALOGEN HEADLAMP]
TURN SIGNAL LAMP CIRCUIT
Rear turn signal lamp
Is the inspection result normal?
YES
>> GO TO 6.
NO
>> GO TO 5.
5.
CHECK TURN SIGNAL LAMP POWER SUPPLY CIRCUIT (SHORT)
1.
Turn ignition switch OFF.
2.
Disconnect BCM connector.
3.
Check continuity between BCM harness connector and ground.
Front turn signal lamp
Side turn signal lamp
Rear turn signal lamp
Is the inspection result normal?
YES
>> Replace BCM. Refer to
BCS-132, "Removal and Installation"
.
NO
>> Repair or replace harness.
6.
CHECK TURN SIGNAL LAMP POWER SUPPLY CIRCUIT (OPEN)
1.
Turn ignition switch OFF.
2.
Disconnect BCM connector.
+
-
Test item
Voltage
(Approx.)
BCM
Connector
Terminal
RH
B3
136
Ground
Turn signal
switch
Right
Center
0 V
LH
133
Left
Center
0 V
PKID0926E
PKID0926E
BCM
—
Continuity
Connector
Terminal
RH
E60
168
Ground
Not existed
LH
167
BCM
—
Continuity
Connector
Terminal
RH
M70
43
Ground
Not existed
LH
42
BCM
—
Continuity
Connector
Terminal
RH
B3
136
Ground
Not existed
LH
133
TURN SIGNAL LAMP CIRCUIT
EXL-295
< DTC/CIRCUIT DIAGNOSIS >
[HALOGEN HEADLAMP]
C
D
E
F
G
H
I
J
K
M
A
B
EXL
N
O
P
3.
Check continuity between BCM harness connector and each turn signal lamp harness connector.
Front turn signal lamp
Side turn signal lamp (LHD models)
Side turn signal lamp (RHD models)
Rear turn signal lamp
Is the inspection result normal?
YES
>> GO TO 7.
NO
>> Repair or replace harness.
7.
CHECK TURN SIGNAL LAMP GROUND CIRCUIT
Check continuity between each turn signal lamp harness connector and ground.
Front turn signal lamp
Side turn signal lamp (LHD models)
Side turn signal lamp (RHD models)
BCM
Front combination lamp
Continuity
Connector
Terminal
Connector
Terminal
RH
E60
168
E92
6
Existed
LH
167
E90
BCM
Door mirror
Continuity
Connector
Terminal
Connector
Terminal
RH
M70
43
D27
13
Existed
LH
42
D3
BCM
Door mirror
Continuity
Connector
Terminal
Connector
Terminal
RH
M70
43
D40
13
Existed
LH
42
D16
BCM
Rear turn signal lamp
Continuity
Connector
Terminal
Connector
Terminal
RH
B3
136
B80
1
Existed
LH
133
B23
Front combination lamp
—
Continuity
Connector
Terminal
RH
E92
1
Ground
Existed
LH
E90
Door mirror
—
Continuity
Connector
Terminal
RH
D27
14
Ground
Existed
LH
D3
Door mirror
—
Continuity
Connector
Terminal
RH
D40
14
Ground
Existed
LH
D16
EXL-296
< DTC/CIRCUIT DIAGNOSIS >
[HALOGEN HEADLAMP]
TURN SIGNAL LAMP CIRCUIT
Rear turn signal lamp
Is the inspection result normal?
YES-1 >> Front turn signal lamp or rear turn signal lamp: GO TO 8.
YES-2 >> Side turn signal lamp: Replace side turn signal lamp. Refer to
EXL-323, "Removal and Installa-
.
NO
>> Repair or replace harness.
8.
CHECK TURN SIGNAL LAMP BULB
Check the applicable turn signal lamp bulb.
Is the inspection result normal?
YES
>> Check the corresponding turn signal lamp bulb socket. Repair or replace if necessary.
NO
>> Replace the corresponding turn signal lamp bulb. Refer to
signal lamp) or
(rear turn signal lamp).
Rear turn signal lamp
—
Continuity
Connector
Terminal
RH
B80
2
Ground
Existed
LH
B23
LIGHT & RAIN SENSOR
EXL-297
< DTC/CIRCUIT DIAGNOSIS >
[HALOGEN HEADLAMP]
C
D
E
F
G
H
I
J
K
M
A
B
EXL
N
O
P
LIGHT & RAIN SENSOR
Component Function Check
INFOID:0000000010469994
1.
CHECK LIGHT & RAIN SENSOR
1.
Clean light & rain sensor detection area of windshield fully.
2.
Turn ignition switch ON.
3.
Turn lighting switch AUTO.
4.
With the light & rain sensor illuminating, check the auto light function.
Is the inspection result normal?
YES
>> Light & rain sensor is normal.
NO
>> Refer to
EXL-297, "Diagnosis Procedure"
.
Diagnosis Procedure
INFOID:0000000010469995
1.
CHECK LIGHT & RAIN SENSOR POWER SUPPLY
1.
Turn ignition switch OFF
2.
Disconnect light & rain sensor connector.
3.
Turn ignition switch ON.
4.
Check voltage between light & rain sensor harness connector and ground.
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> GO TO 2.
2.
CHECK LIGHT & RAIN SENSOR POWER SUPPLY CIRCUIT
1.
Turn ignition switch OFF.
2.
Remove room lamp relay.
3.
Check continuity between room lamp relay harness connector and light & rain sensor harness connector.
Is the inspection result normal?
YES
>> Perform the interior room lamp power supply circuit diagnosis. Refer to
.
NO
>> Repair or replace harness.
3.
CHECK LIGHT & RAIN SENSOR GROUND CIRCUIT
Check continuity between light & rain sensor harness connector and ground.
Condition
Auto light function
Light & rain sensor
When illuminating
Not operating
When shutting off light
Operating
+
-
Voltage
Light & rain sensor
Connector
Terminal
R5
1
Ground Battery
voltage
Room lamp relay
Light & rain sensor
Continuity
Connector
Terminal
Connector
Terminal
M80
7
R5
1
Existed
Light & rain sensor
—
Continuity
Connector
Terminal
R5
3
Ground
Existed
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст