Nissan Qashqai J11. Manual — part 1746
EXL-286
< DTC/CIRCUIT DIAGNOSIS >
[HALOGEN HEADLAMP]
STOP LAMP CIRCUIT
High-mounted stop lamp
Is the inspection result normal?
YES
>> GO TO 9.
NO
>> GO TO 8.
8.
CHECK STOP LAMP / HIGH-MOUNTED STOP LAMP POWER SUPPLY CIRCUIT (SHORT)
1.
Turn ignition switch OFF.
2.
Disconnect BCM connector.
3.
Check continuity between BCM harness connector and ground.
Stop lamp
High-mounted stop lamp
Is the inspection result normal?
YES
>> Replace BCM. Refer to
BCS-132, "Removal and Installation"
.
NO
>> Repair or replace harness.
9.
CHECK STOP LAMP / HIGH-MOUNTED STOP LAMP POWER SUPPLY CIRCUIT (OPEN)
1.
Turn ignition switch OFF.
2.
Disconnect BCM connector.
3.
Check continuity between BCM harness connector and each stop lamp harness connector.
Stop lamp
High-mounted stop lamp
Is the inspection result normal?
YES
>> GO TO 10.
NO
>> Repair or replace harness.
10.
CHECK STOP LAMP / HIGH-MOUNTED STOP LAMP GROUND CIRCUIT
Check continuity between each stop lamp harness connector and ground.
+
-
Test item
Voltage
(Approx.)
BCM
Connector
Terminal
B4
39
Ground
STOP LAMP 3
On
9 – 16 V
Off
0 V
BCM
—
Continuity
Connector
Terminal
RH
B3
134
Ground
Not existed
LH
129
BCM
—
Continuity
Connector
Terminal
B4
39
Ground
Not existed
BCM
Stop lamp / tail lamp
Continuity
Connector
Terminal
Connector
Terminal
RH
B3
134
B79
1
Existed
LH
129
B22
BCM
High-mounted stop lamp
Continuity
Connector
Terminal
Connector
Terminal
B4
39
B17
2
Existed
STOP LAMP CIRCUIT
EXL-287
< DTC/CIRCUIT DIAGNOSIS >
[HALOGEN HEADLAMP]
C
D
E
F
G
H
I
J
K
M
A
B
EXL
N
O
P
Stop lamp
High-mounted stop lamp
Is the inspection result normal?
YES-1 >> Stop lamp: Replace the corresponding rear combination lamp. Refer to
YES-2 >> High-mounted stop lamp: Replace high-mounted stop lamp. Refer to
NO
>> Repair or replace harness.
Component Inspection
INFOID:0000000010469986
1.
CHECK STOP LAMP SWITCH-1
1.
Turn ignition switch OFF.
2.
Disconnect stop lamp switch connector.
3.
Check continuity of stop lamp switch terminals.
Is the inspection result normal?
YES
>> INSPECTION END
NO
>> GO TO 2.
2.
CHECK STOP LAMP SWITCH-2
1.
Adjust stop lamp switch installation. Refer to
BR-8, "Inspection and Adjustment"
(RHD models).
2.
Check continuity of stop lamp switch terminals.
Is the inspection result normal?
YES
>> INSPECTION END
NO
>> Replace stop lamp switch. Refer to
(LHD models) or
(RHD models).
Stop lamp / tail lamp
—
Continuity
Connector
Terminal
RH
B79
2
Ground
Existed
LH
B22
High-mounted stop lamp
—
Continuity
Connector
Terminal
B17
3
Ground
Existed
Stop lamp switch
Condition
Continuity
Terminal
1
2
Brake pedal
Depressed
Existed
Fully released
Not existed
Stop lamp switch
Condition
Continuity
Terminal
1
2
Brake pedal
Depressed
Existed
Fully released
Not existed
EXL-288
< DTC/CIRCUIT DIAGNOSIS >
[HALOGEN HEADLAMP]
FRONT FOG LAMP CIRCUIT
FRONT FOG LAMP CIRCUIT
Component Function Check
INFOID:0000000010469987
1.
CHECK FRONT FOG LAMP OPERATION
With CONSULT
1.
Select “FRONT FOG LAMP” in “Active Test” mode of “IPDM E/R” using CONSULT.
2.
With operating the test items, check that the front fog lamp is turned ON.
Is the inspection result normal?
YES
>> Front fog lamp circuit is normal.
NO
>> Refer to
EXL-288, "Diagnosis Procedure"
.
Diagnosis Procedure
INFOID:0000000010469988
1.
CHECK FRONT FOG LAMP OUTPUT VOLTAGE
With CONSULT
1.
Turn ignition switch OFF.
2.
Disconnect front fog lamp connector.
3.
Turn ignition switch ON.
4.
Select “FRONT FOG LAMP” in “Active Test” mode of “IPDM E/R” using CONSULT.
5.
With operating the test items, check voltage between IPDM E/R harness connector and ground.
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> Replace IPDM E/R. Refer to
PCS-67, "Removal and Installation"
2.
CHECK FRONT FOG LAMP POWER SUPPLY CIRCUIT
1.
Turn ignition switch OFF.
2.
Disconnect IPDM E/R connector.
3.
Check continuity between IPDM E/R harness connector and front fog lamp harness connector.
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> Repair or replace harness.
3.
CHECK FRONT FOG LAMP GROUND CIRCUIT
Check continuity between front fog lamp harness connector and ground.
On
: Front fog lamp ON
Off
: Front fog lamp OFF
+
-
Test item
Voltage
IPDM E/R
Connector
Terminal
RH
E101
49
Ground
FRONT FOG
LAMP
On
9 – 16 V
Off
0 – 1 V
LH
E102
59
On
9 – 16 V
Off
0 – 1 V
IPDM E/R
Front fog lamp
Continuity
Connector
Terminal
Connector
Terminal
RH
E101
49
E95
1
Existed
LH
E102
59
E94
FRONT FOG LAMP CIRCUIT
EXL-289
< DTC/CIRCUIT DIAGNOSIS >
[HALOGEN HEADLAMP]
C
D
E
F
G
H
I
J
K
M
A
B
EXL
N
O
P
Is the inspection result normal?
YES
>> Replace the corresponding front fog lamp bulb. Refer to
NO
>> Repair or replace harness.
Front fog lamp
—
Continuity
Connector
Terminal
RH
E95
2
Ground
Existed
LH
E94
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст