Nissan Qashqai J11. Manual — part 122
OIL SEAL
EM-427
< REMOVAL AND INSTALLATION >
[R9M]
C
D
E
F
G
H
I
J
K
L
M
A
EM
N
P
O
OIL SEAL
FRONT OIL SEAL
FRONT OIL SEAL : Removal and Installation
INFOID:0000000010282011
REMOVAL
1.
Remove the following parts.
• Front fender protector (RH): Refer to
• Drive belt: Refer to
EM-373, "Removal and Installation"
.
• Crankshaft pulley: Refer to
.
2.
Remove front oil seal using service tool (A).
NOTE:
The service tool is supplied in the new seal parts kit.
INSTALLATION
1.
Install front oil seal with the following procedure:
a.
Fit the protector (A) to front oil seal (1).
• Align the front oil seal notches with front cover notches.
NOTE:
The protector is supplied in the new seal parts kit.
b.
Tighten to front oil seal (1) using service tool (A).
NOTE:
The service tool is supplied in the new seal parts kit.
c.
Remove the protector.
2.
Install in the reverse order of removal, for the rest of parts.
REAR OIL SEAL
REAR OIL SEAL : Removal and Installation
INFOID:0000000010282012
REMOVAL
1.
Remove transaxle assembly. Refer to
JPBIA0765ZZ
JPBIA0778ZZ
: 47 N·m (4.8 kg-m, 35 ft-lb)
JPBIA0591ZZ
EM-428
< REMOVAL AND INSTALLATION >
[R9M]
OIL SEAL
2.
Remove clutch cover and clutch disk. Refer to
CL-26, "R9M : Removal and Installation"
.
3.
Remove rear oil seal retainer.
INSTALLATION
1.
Install rear oil seal retainer with the following procedure:
a.
Set guide bolt (A) and protector (B) to rear oil seal retainer (1).
NOTE:
The protector is supplied in the new seal parts kit.
b.
Move the rear oil seal retainer evenly by hand until it makes con-
tact with the cylinder block.
c.
Remove guide bolts and protector.
d.
Tighten mounting bolts in two steps separately in numerical
order as shown in the figure.
i.
Tighten bolts No. 1and 5.
ii.
Tighten No. 1 to 8 in numerical order as shown.
2.
Install in the reverse order of removal, for the rest of parts.
JPBIA0777ZZ
: 5.0 N·m (0.51 kg-m, 44 in-lb)
: 12.0 N·m (1,2 kg-m, 9 ft-lb)
JPBIA0645ZZ
ENGINE ASSEMBLY
EM-429
< UNIT REMOVAL AND INSTALLATION >
[R9M]
C
D
E
F
G
H
I
J
K
L
M
A
EM
N
P
O
UNIT REMOVAL AND INSTALLATION
ENGINE ASSEMBLY
Exploded View
INFOID:0000000010282013
2WD
4WD
E1BIA1212GB
1.
Upper torque rod
2.
Engine mounting insulator (RH)
3.
Engine mounting insulator (LH)
4.
Engine mounting frame support (LH) 5.
Engine mounting bracket (LH)
6.
Rear torque rod
7.
Rear engine mounting bracket
Refer to
for symbols in the figure.
EM-430
< UNIT REMOVAL AND INSTALLATION >
[R9M]
ENGINE ASSEMBLY
CVT
E1BIA1213GB
1.
Upper torque rod
2.
Engine mounting insulator (RH)
3.
Engine mounting insulator (LH)
4.
Engine mounting frame support (LH) 5.
Engine mounting bracket (LH)
6.
Rear torque rod
7.
Rear engine mounting bracket
Refer to
for symbols in the figure.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст