Nissan Qashqai J11. Manual — part 120
TIMING SPROCKET
EM-419
< REMOVAL AND INSTALLATION >
[R9M]
C
D
E
F
G
H
I
J
K
L
M
A
EM
N
P
O
TIMING SPROCKET
Removal and installation
INFOID:0000000010282007
REMOVAL
1.
Remove the timing chain. Refer to
.
2.
Immobilise the intake camshaft timing sprocket using the tool
[SST: -(Mot.1969)] (1)
3.
Loosen the intake camshaft timing sprocket bolt (2).
4.
Remove the tool [SST: -(Mot.1969)] .
5.
Place a screw driver in the hole (2), compress the spring of the
intake camshaft timing sprocket (1) and remove the exhaust
camshaft timing sprocket (rear) (3).
6.
Remove. Refer to
a.
the screwdriver,
b.
the intake camshaft timing sprocket bolt,
c.
the intake camshaft timing sprocket spacer,
d.
the intake camshaft timing sprocket.
INSTALLATION
1.
Install the intake camshaft timing sprocket with the following procedure:
a.
Set the intake camshaft timing sprocket (1) on base plate of
positioning tool [SST: — (Mot. 1773)] (A).
E1BIA0455ZZ
E1BIA0456ZZ
JPBIA0766ZZ
EM-420
< REMOVAL AND INSTALLATION >
[R9M]
TIMING SPROCKET
b.
Set the lever (B) in the lower gear teeth (A). Pivot the lever
counterclockwise until the two gear teeth are aligned.
c.
Set a stopper pin (A) in the gear hole.
NOTE:
• Use approximately 4.0 mm (0.157 in) dia. hard metal pin as a
stopper pin
d.
Install intake camshaft timing sprocket (1) and intake camshaft
timing sprocket spacer (2) to the camshaft.
e.
Align matching mark (B) on intake camshaft timing sprocket and
mark (A) of cylinder head housing.
f.
Temporarily tighten mounting bolt.
2.
Install exhaust camshaft timing sprocket (rear) with the following procedure:
a.
Check that the exhaust camshaft groove (1) is horizontal (large ring facing upwards).
b.
Center the exhaust camshaft timing sprocket (rear) openings on
the camshaft hub mounting holes (2).
c.
Set the exhaust camshaft timing sprocket (rear) fully onto the
camshaft (right side) hub.
d.
Remove stopper pin.
3.
Re-install the tool [SST: -(Mot.1969)] to immobilise the intake camshaft timing sprocket.
4.
Tighten the intake camshaft timing sprocket bolts
5.
Turn 35 degrees clockwise (angle tightning).
6.
Install in the reverse order of removal.
1
: Wear compensation gear
JPBIA0594ZZ
1
: Wear compensation gear
JPBIA0595ZZ
C : Stopper pin
JPBIA0616ZZ
E1BIA0462ZZ
Intake camshaft timing
sprocket bolt:
20 Nm (2.0 kg-m, 15 ft-lb)
CAMSHAFT
EM-421
< REMOVAL AND INSTALLATION >
[R9M]
C
D
E
F
G
H
I
J
K
L
M
A
EM
N
P
O
CAMSHAFT
Exploded View
INFOID:0000000010282008
Removal and Installation
INFOID:0000000010282009
REMOVAL
1.
Remove the following parts.
• Oil separator: Refer to
• Fuel injector: Refer to
• Engine slinger (front side): Refer to
• Front cover and timing chain related parts: Refer to
.
• Fuel pump: Refer to
.
• Vacuum pump: Refer to
.
2.
Remove camshaft position sensor.
1.
Camshaft position sensor
2.
O-ring
3.
Cylinder head housing
4.
Timing sprocket spacer
5.
Exhaust camshaft timing sprocket
(front)
6.
Exhaust camshaft timing sprocket
(rear)
7.
Intake camshaft timing sprocket
spacer
8.
Intake camshaft timing sprocket
9.
Exhaust camshaft
10. Camshaft sprocket (for fuel pump)
11.
Intake camshaft
12. Camshaft bracket
13. Camshaft bracket
14. Camshaft bracket
15. Camshaft bracket
16. Camshaft bracket pin
A.
or
B.
Refer to
Refer to
for symbols shown in the figure.
E1BIA0576GB
EM-422
< REMOVAL AND INSTALLATION >
[R9M]
CAMSHAFT
CAUTION:
• Handle camshaft position sensor carefully and avoid impacts.
• Never disassemble camshaft position sensor.
• Never place sensor where it is exposed to magnetism.
3.
Remove cylinder head housing with the following procedure:
a.
Loosen mounting bolts in reverse order as shown in the figure.
b.
Remove the cylinder head housing (1) using a flat-blade screw-
driver (A).
CAUTION:
Be careful not to damage the mating surface.
4.
Remove camshafts with the following procedure:
a.
Install cylinder head housing (1) to cylinder head stand [com-
mercial service tool: KV113B0200 (Mot.1573)] (A).
b.
Loosen mounting bolts, and remove camshaft brackets and
camshafts.
• Mark camshafts and camshaft brackets so they are placed in
the same position and direction for installation.
: Engine front
B
: Protective shim (suitable tool)
E1BIA0605ZZ
JPBIA0606ZZ
JPBIA0641ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст