Nissan Qashqai J11. Manual — part 710
TRANSAXLE ASSEMBLY
TM-415
< UNIT REMOVAL AND INSTALLATION >
[CVT: RE0F10D]
C
E
F
G
H
I
J
K
L
M
A
B
TM
N
O
P
UNIT REMOVAL AND INSTALLATION
TRANSAXLE ASSEMBLY
Exploded View
INFOID:0000000010589407
Removal and Installation
INFOID:0000000010589408
REMOVAL
WARNING:
Never remove the radiator cap when the engine is hot. Serious burns could occur from high pressure
coolant escaping from the radiator. Wrap a thick cloth around the cap. Slowly turn a quarter turn to
allow built-up pressure to escape. Carefully remove the cap by turning it all the way.
CAUTION:
• Perform when the engine is cold.
• When replacing TCM and transaxle assembly simultaneously, perform “ADDITIONAL SERVICE
WHEN REPLACING TCM AND TRANSAXLE ASSEMBLY” before work. Refer to
.
NOTE:
When removing components such as hoses, tubes/lines, etc., cap or plug openings to prevent fluid from spill-
ing.
Transaxle assembly
O-ring
CVT fluid charging pipe
CVT fluid charging pipe cap
: For the tightening torque, refer to
TM-415, "Removal and Installation"
.
: Always replace after every disassembly.
: N·m (kg-m, ft-lb)
: N·m (kg-m, in-lb)
: Apply petroleum jelly
JSDIA5327GB
TM-416
< UNIT REMOVAL AND INSTALLATION >
[CVT: RE0F10D]
TRANSAXLE ASSEMBLY
1.
Remove engine and transaxle assembly from the vehicle. Refer to
EM-173, "Removal and Installation"
2.
Remove starter motor. Refer to
STR-25, "MR20DD : Exploded View"
3.
Remove transfer assembly. Refer to
DLN-76, "Removal and Installation"
. (4WD models only)
4.
Remove the CVT water hoses from engine side. Refer to
.
5.
Turn crankshaft, and remove the tightening nuts for drive plate and torque converter.
CAUTION:
Rotate crankshaft clockwise (as viewed from the crankshaft pulley side).
6.
Remove the bolts that fasten the transaxle assembly and engine assembly.
7.
Separate the engine from the transaxle assembly.
NOTE:
Using paint, put matching marks on the drive plate and torque converter when removing the torque con-
verter to drive plate nuts.
8.
Remove following parts from transaxle assembly.
• Control cable bracket (Refer to
.)
• Air breather hose (Refer to
• CVT water hoses and heater thermostat (Refer to
.)
• CVT fluid cooler hose and tube (Refer to
• Charging pipe and O-ring
INSTALLATION
Note the followings and installation is in the reverse order of removal.
CAUTION:
• Write down the serial number of the new transaxle assembly.
• When replacing an engine or transaxle you must make sure any dowels are installed correctly during
re-assembly
• Improper alignment caused by missing dowels may cause vibration, oil leaks or breakage of drive
train components.
• Never reuse O-rings or copper sealing washers.
• When turning crankshaft, turn it clockwise as viewed from the front of the engine.
• When tightening the nuts for the torque converter while securing the crankshaft pulley bolt, be sure
to confirm the tightening torque of the crankshaft pulley bolt. Refer to
• After converter is installed to drive plate, rotate crankshaft several turns to check that CVT rotates
freely without binding.
• When installing the CVT to the engine, align the matching mark on the drive plate with the matching
mark on the torque converter.
• When installing the drive plate to torque converter nuts, tighten them temporarily. Then, tighten the nuts to
the specified torque.
• Install the transaxle assembly and engine assembly mounting bolts according to the following standards.
JSDIA6075GB
TRANSAXLE ASSEMBLY
TM-417
< UNIT REMOVAL AND INSTALLATION >
[CVT: RE0F10D]
C
E
F
G
H
I
J
K
L
M
A
B
TM
N
O
P
Inspection and Adjustment
INFOID:0000000010589409
INSPECTION BEFORE INSTALLATION
After inserting a torque converter to the CVT, check dimension (A)
with in the reference value limit.
INSPECTION AFTER INSTALLATION
Check the following items:
• Start the engine and check visually that there is no leakage of CVT fluid and engine coolant.
• For CVT position, refer to
.
ADJUSTMENT AFTER INSTALLATION
• Adjust the CVT fluid level. Refer to
• When replaced transaxle assembly, perform "ADDITIONAL SERVICE WHEN REPLACING TRANSAXLE
ASSEMBLY". Refer to
.
Bolt No.
Insertion direction
Transaxle to engine
Engine to transaxle
Number of bolts
1
7
Bolt length
mm (in)
55 (2.17)
50 (1.97)
Tightening torque
N·m (kg-m, ft-lb)
62 (6.3, 46)
JSDIA5265ZZ
B
: Scale
C
: Straightedge
Dimension (A)
: Refer to
.
JPDIA0115ZZ
TM-418
< UNIT DISASSEMBLY AND ASSEMBLY >
[CVT: RE0F10D]
TORQUE CONVERTER AND CONVERTER HOUSING OIL SEAL
UNIT DISASSEMBLY AND ASSEMBLY
TORQUE CONVERTER AND CONVERTER HOUSING OIL SEAL
Exploded View
INFOID:0000000010589410
Disassembly
INFOID:0000000010589411
1.
Remove transaxle assembly. Refer to
TM-415, "Removal and Installation"
2.
Remove torque converter from transaxle assembly.
CAUTION:
Never damage the bushing on the inside of torque converter sleeve when removing torque con-
verter.
3.
Remove O-ring from input shaft.
4.
Remove converter housing oil seal using an oil seal remover (commercial service tool).
CAUTION:
Be careful not to scratch converter housing.
Assembly
INFOID:0000000010589412
Note the followings and assembly is in the reverse order of disassembly.
CAUTION:
• Never reuse O-ring.
• Never reuse converter housing oil seal.
• Apply CVT fluid to O-ring.
• Apply CVT fluid to converter housing oil seal.
Torque converter
O-ring
Converter housing oil seal
Transaxle assembly
: Always replace after every disassembly.
: Apply CVT fluid
JSDIA4173ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст