Nissan Qashqai J11. Manual — part 708
WATER HOSE
TM-407
< REMOVAL AND INSTALLATION >
[CVT: RE0F10D]
C
E
F
G
H
I
J
K
L
M
A
B
TM
N
O
P
-
Place dial indicator (A) on the pellet
and measure the elonga-
tion from the initial state.
4.
If out of standard, replace heater thermostat.
INSPECTION AFTER INSTALLATION
Start the engine and check visually that there is no leakage of engine coolant.
Standard
: Refer to
.
JSDIA3662ZZ
TM-408
< REMOVAL AND INSTALLATION >
[CVT: RE0F10D]
FLUID COOLER SYSTEM
FLUID COOLER SYSTEM
Exploded View
INFOID:0000000010589397
Transaxle side
Vehicle side
JSDIA5320GB
Transaxle assembly
Copper washer
Fluid cooler tube A
Fluid cooler tube B
Hose clamp
Fluid cooler hose A
CVT oil warmer
: Always replace after every disassembly.
: N·m (kg-m, ft-lb)
JSDIA5319GB
FLUID COOLER SYSTEM
TM-409
< REMOVAL AND INSTALLATION >
[CVT: RE0F10D]
C
E
F
G
H
I
J
K
L
M
A
B
TM
N
O
P
Removal and Installation
INFOID:0000000010589398
REMOVAL
NOTE:
When removing components such as hoses, tubes/lines, etc., cap or plug openings to prevent fluid from spill-
ing.
1.
Remove front bumper. Refer to
EXT-19, "Removal and Installation"
2.
Remove engine under cover. Refer to
EXT-35, "ENGINE UNDER COVER : Removal and Installation"
3.
Remove the battery mounting bracket assembly and battery mounting bracket. Refer to
4.
Remove the harness bracket mounting nuts (
) and remove
the harness bracket
from the vehicle.
5.
Remove hose clamps of CVT cooler hose F and B to remove the
hose on the CVT oil warmer side.
6.
Remove hose clamp (
) of CVT fluid cooler
to remove the
hose on the CVT fluid cooler side.
7.
Remove bracket mounting nut (
) to remove fluid cooler hose
B, C, E, and F together with fluid cooler tube assembly A.
Bumper reinforcement
Bracket
Bracket
CVT fluid cooler
Hose clamp
Fluid cooler hose D
Fluid cooler tube assembly B
Bumper reinforcement lower
Fluid cooler hose E
Fluid cooler hose C
Bracket
Fluid cooler tube assembly A
Fluid cooler hose B
Fluid cooler hose F
Front side member LH
Transaxle assembly
CVT oil warmer
Fluid cooler tube A
: Always replace after every disassembly.
: N·m (kg-m, in-lb)
: Vehicle front
JSDIA6041ZZ
JSDIA5412ZZ
JSDIA5413ZZ
TM-410
< REMOVAL AND INSTALLATION >
[CVT: RE0F10D]
FLUID COOLER SYSTEM
8.
Remove the bracket mounting bolts (
) and remove the CVT
fluid cooler from the vehicle.
9.
Remove fluid cooler hose D.
10. Remove the fluid cooler tube assembly B from CVT fluid cooler.
11. Remove hose clamp of fluid cooler hose A to remove the hose
on the CVT oil warmer side.
12. Remove fluid cooler tube A and fluid cooler tube B.
INSTALLATION
Note the followings and Installation is in the reverse order of removal.
CAUTION:
• Be careful not to damage CVT fluid cooler.
• Never reuse hose clamps.
Transaxle side
Refer to the followings when installing CVT fluid cooler tubes.
• When installing fluid cooler tube A
and fluid cooler tube B
to
transaxle assembly, contact fluid cooler tubes stopper
and
to
transaxle case.
• Refer to the followings when installing fluid cooler hose.
• Refer to the followings when installing hose clamp.
CAUTION:
Hose clamp should not interfere with the bulge of tube.
Vehicle side
JSDIA5414ZZ
JSDIA5321ZZ
Hose
Installation side
tube
Direction of paint mark
Hose insertion depth
(A)
Fluid cooler
hose A
CVT oil warmer
Frontward
Hose end reaches the
end of tube.
CVT fluid cooler
tube B
Align with the paint
marks on the CVT fluid
cooler tube B
SCIA7203E
Hose
Installation side
tube
Hose clamp
Direction of tab
Clamping position
Fluid cooler
hose A
CVT oil warmer
Frontward
5 - 9 MM. (0.20 - 0.35
in) (A) from hose end
CVT fluid cooler
tube B
JSDIA2424ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст