Nissan Qashqai J11. Manual — part 919
PB-58
< BASIC INSPECTION >
RELEASE OF REAR BRAKE CALIPER
RELEASE OF REAR BRAKE CALIPER
Description
INFOID:0000000010833871
CAUTION:
When the following operations are performed, always use CONSULT, for performing “BRAKE
RELEASE” of “WORK SUPPORT”.
×
: Required
—: not required
Work Procedure
INFOID:0000000010833872
CAUTION:
When the following operations are performed, always use CONSULT. (It cannot be performed by any
means other than CONSULT.)
• Removing/installing electric parking brake control module
• Replacing electric parking brake control module
• Removing/installing rear brake pad (When not pressing piston of rear brake caliper assembly)
• Removing/installing rear brake pad (When pressing piston of rear brake caliper assembly)
• Replacing rear brake pad
• Removing/installing rear brake caliper assembly
• Replacing rear brake caliper assembly
NOTE:
When the replaced rear brake pad, refer to
1.
PERFORM BRAKE OPERATION
With CONSULT
1.
Select “EHS/PKB”, “WORK SUPPORT”, and “BRAKE OPERATION” according to this order.
CAUTION:
• Never operate the parking brake switch.
• Never depress the brake pedal.
2.
Touch “START”.
>> GO TO 2.
2.
PERFORM BRAKE RELEASE
With CONSULT
1.
Select “EHS/PKB”, “WORK SUPPORT”, and “BRAKE RELEASE” according to this order.
CAUTION:
• Never operate the parking brake switch.
• Never depress the brake pedal.
Procedure
BRAKE RELEASE
Removing/installing electric parking brake control module
×
Replacing electric parking brake control module
×
Removing/installing rear brake pad (When not pressing piston of rear
brake caliper assembly)
×
Removing/installing rear brake pad (When pressing piston of rear brake
caliper assembly)
×
Replacing rear brake pad
×
Removing/installing rear brake caliper assembly
×
Replacing rear brake caliper assembly
×
Removing/installing parking brake switch
—
Replacing parking brake switch
—
Removing/installing clutch stroke sensor
—
Replacing clutch stroke sensor
—
Removing/installing clutch pedal
—
Replacing clutch pedal
—
CHANGE OF SYSTEM MODE
PB-59
< BASIC INSPECTION >
C
D
E
G
H
I
J
K
L
M
A
B
PB
N
O
P
CHANGE OF SYSTEM MODE
Description
INFOID:0000000010833873
CAUTION:
When the following operations are performed, always use CONSULT, for performing “SYSTEM MODE
CHANGE” of “WORK SUPPORT”.
×
: Required
—: not required
Work Procedure
INFOID:0000000010833874
CAUTION:
When performing the following operations, always use CONSULT. (It cannot be performed by any
means other than CONSULT.)
• Replacing electric parking brake control module
1.
CONFIGURATION
Perform the configuration. Refer to
.
>> GO TO 2.
2.
CALIBRATION OF G SENSOR
Perform the calibration of G sensor. Refer to
.
>> GO TO 3.
3.
RESET OF CLUTCH PEDAL STROKE SENSOR
Perform the reset of clutch stroke sensor. Refer to
>> GO TO 4.
4.
ADJUSTMENT OF REAR BRAKE CALIPER INITIAL POSITION
Perform the adjustment of rear brake caliper initial position: Refer to
>> GO TO 5.
5.
OPERATION OF REAR BRAKE CALIPER
Perform the operation of rear brake caliper: Refer to
>> GO TO 6.
6.
RELEASE OF REAR BRAKE CALIPER
Perform the release of rear brake caliper: Refer to
Procedure
SYSTEM MODE CHANGE
Removing/installing electric parking brake control module
—
Replacing electric parking brake control module
×
Removing/installing rear brake pad (When not pressing piston of rear
brake caliper assembly)
—
Replacing rear brake caliper assembly
—
Removing/installing parking brake switch
—
Replacing parking brake switch
—
Removing/installing clutch stroke sensor
—
Replacing clutch stroke sensor
—
Removing/installing clutch pedal
—
Replacing clutch pedal
—
PB-60
< BASIC INSPECTION >
CHANGE OF SYSTEM MODE
CHANGE OF SYSTEM MODE
Description
INFOID:0000000010833873
CAUTION:
When the following operations are performed, always use CONSULT, for performing “SYSTEM MODE
CHANGE” of “WORK SUPPORT”.
×
: Required
—: not required
Work Procedure
INFOID:0000000010833874
CAUTION:
When performing the following operations, always use CONSULT. (It cannot be performed by any
means other than CONSULT.)
• Replacing electric parking brake control module
1.
CONFIGURATION
Perform the configuration. Refer to
.
>> GO TO 2.
2.
CALIBRATION OF G SENSOR
Perform the calibration of G sensor. Refer to
.
>> GO TO 3.
3.
RESET OF CLUTCH PEDAL STROKE SENSOR
Perform the reset of clutch stroke sensor. Refer to
>> GO TO 4.
4.
ADJUSTMENT OF REAR BRAKE CALIPER INITIAL POSITION
Perform the adjustment of rear brake caliper initial position: Refer to
>> GO TO 5.
5.
OPERATION OF REAR BRAKE CALIPER
Perform the operation of rear brake caliper: Refer to
>> GO TO 6.
6.
RELEASE OF REAR BRAKE CALIPER
Perform the release of rear brake caliper: Refer to
Procedure
SYSTEM MODE CHANGE
Removing/installing electric parking brake control module
—
Replacing electric parking brake control module
×
Removing/installing rear brake pad (When not pressing piston of rear
brake caliper assembly)
—
Replacing rear brake caliper assembly
—
Removing/installing parking brake switch
—
Replacing parking brake switch
—
Removing/installing clutch stroke sensor
—
Replacing clutch stroke sensor
—
Removing/installing clutch pedal
—
Replacing clutch pedal
—
C10C8 ELECTRIC PARKING BRAKE CONTROL MODULE
PB-61
< DTC/CIRCUIT DIAGNOSIS >
C
D
E
G
H
I
J
K
L
M
A
B
PB
N
O
P
DTC/CIRCUIT DIAGNOSIS
C10C8 ELECTRIC PARKING BRAKE CONTROL MODULE
DTC Description
INFOID:0000000010833649
DTC DETECTION LOGIC
POSSIBLE CAUSE
• Harness or connector
• Electric parking brake control module
• Parking brake switch
FAIL-SAFE
Type 1
Only mechanical release is available.
Type 2
Only mechanical release is available.
Type 3
Only mechanical release is available.
Type 4
Only mechanical release is available.
Type 5
Automatic apply and release are prohibited.
DTC CONFIRMATION PROCEDURE
1.
PRECONDITIONING
If “DTC CONFIRMATION PROCEDURE” has been previously conducted, always turn the ignition switch OFF
and wait at least 10 seconds before conducting the next test.
>> GO TO 2.
2.
CHECK DTC DETECTION
With CONSULT
1.
Turn the ignition switch OFF to ON.
CAUTION:
Be sure to wait for 10 seconds after turning ignition switch OFF or ON.
2.
Push the parking brake switch.
CAUTION:
DTC
Display Item
(Trouble diagnosis content)
Malfunction detected condition
Type
C10C8
CONTROL MODULE
(CONTROL MODULE)
INTERNAL ELECTRIC
MALFNCTN
(INTERNAL ELECTRIC
MALFNCTN)
When there is an internal malfunction in the electric park-
ing brake control module. (Malfunction of hardware)
1
WATCHDOG/SAFETY
µ
C
ERROR
(Watchdog/safety
µ
C error)
When there is an internal malfunction in the electric park-
ing brake control module. (Malfunction of communica-
tion)
2
SUPERVISION SOFT-
WARE ERROR
(Supervision software error)
When there is an internal malfunction in the electric park-
ing brake control module. (Malfunction of software)
3
EVENT INFORMATION
(Event information)
When there is an internal malfunction in the electric park-
ing brake control module. (Maintenance mode)
4
NOT CONFIGURED
(Not configured)
When variant coding is incomplete.
5
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст