Nissan Qashqai J11. Manual — part 918
PB-54
< BASIC INSPECTION >
RESET OF CLUTCH STROKE SENSOR
RESET OF CLUTCH STROKE SENSOR
Description
INFOID:0000000010833867
CAUTION:
When the following operations are performed, always use CONSULT, and carry “CLUTCH SENSOR
RESET” of “WORK SUPPORT”.
×
: Required
—: not required
Work Procedure
INFOID:0000000010833868
CAUTION:
When the following operations are performed, always use CONSULT. (It cannot be performed by any
means other than CONSULT.)
• Replacing electric parking brake control module
• Removing/installing clutch stroke sensor
• Replacing clutch stroke sensor
• Removing/installing clutch pedal
• Replacing clutch pedal
1.
CHECK THE VEHICLE STATUS
1.
Stop the vehicle.
2.
Stop the engine.
3.
Turn the ignition switch OFF.
>> GO TO 2.
2.
CHECKING INSTALLATION CONDITION OF CLUTCH COMPONENTS
Check the installation conditions of clutch components.
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> Repair or replace error-detected parts and GO TO 3.
3.
PERFORM CLUTCH SENSOR RESET
CAUTION:
• Never allow passenger or load on the vehicle.
• Never apply vibration to the vehicle body when opening or closing door during calibration.
With CONSULT
1.
Turn the ignition switch ON.
Procedure
CLUTCH SENSOR RESET
Removing/installing electric parking brake control module
—
Replacing electric parking brake control module
×
Removing/installing rear brake pad (When not pressing piston of rear
brake caliper assembly)
—
Removing/installing rear brake pad (When pressing piston of rear brake
caliper assembly)
—
Replacing rear brake pad
—
Removing/installing rear brake caliper assembly
—
Replacing rear brake caliper assembly
—
Removing/installing parking brake switch
—
Replacing parking brake switch
—
Removing/installing clutch stroke sensor
×
Replacing clutch stroke sensor
×
Removing/installing clutch pedal
×
Replacing clutch pedal
×
OPERATION OF REAR BRAKE CALIPER
PB-55
< BASIC INSPECTION >
C
D
E
G
H
I
J
K
L
M
A
B
PB
N
O
P
OPERATION OF REAR BRAKE CALIPER
Description
INFOID:0000000010833869
CAUTION:
When the following operations are performed, always use CONSULT, for performing “BRAKE OPERA-
TION” of “WORK SUPPORT”.
×
: Required
—: not required
Work Procedure
INFOID:0000000010833870
CAUTION:
When the following operations are performed, always use CONSULT. (It cannot be performed by any
means other than CONSULT.)
• Removing/installing electric parking brake control module
• Replacing electric parking brake control module
• Removing/installing rear brake pad (When not pressing piston of rear brake caliper assembly)
• Removing/installing rear brake pad (When pressing piston of rear brake caliper assembly)
• Replacing rear brake pad
• Removing/installing rear brake caliper assembly
• Replacing rear brake caliper assembly
NOTE:
When the replaced rear brake pad, refer to
1.
PERFORM BRAKE OPERATION
With CONSULT
1.
Select “EHS/PKB”, “WORK SUPPORT”, and “BRAKE OPERATION” according to this order.
CAUTION:
• Never operate the parking brake switch.
• Never depress the brake pedal.
2.
Touch “START”.
>> GO TO 2.
2.
PERFORM BRAKE RELEASE
With CONSULT
1.
Select “EHS/PKB”, “WORK SUPPORT”, and “BRAKE RELEASE” according to this order.
CAUTION:
• Never operate the parking brake switch.
• Never depress the brake pedal.
Procedure
BRAKE OPERATION
Removing/installing electric parking brake control module
×
Replacing electric parking brake control module
×
Removing/installing rear brake pad (When not pressing piston of rear
brake caliper assembly)
×
Removing/installing rear brake pad (When pressing piston of rear brake
caliper assembly)
×
Replacing rear brake pad
×
Removing/installing rear brake caliper assembly
×
Replacing rear brake caliper assembly
×
Removing/installing parking brake switch
—
Replacing parking brake switch
—
Removing/installing clutch stroke sensor
—
Replacing clutch stroke sensor
—
Removing/installing clutch pedal
—
Replacing clutch pedal
—
PB-56
< BASIC INSPECTION >
OPERATION OF REAR BRAKE CALIPER
OPERATION OF REAR BRAKE CALIPER
Description
INFOID:0000000010833869
CAUTION:
When the following operations are performed, always use CONSULT, for performing “BRAKE OPERA-
TION” of “WORK SUPPORT”.
×
: Required
—: not required
Work Procedure
INFOID:0000000010833870
CAUTION:
When the following operations are performed, always use CONSULT. (It cannot be performed by any
means other than CONSULT.)
• Removing/installing electric parking brake control module
• Replacing electric parking brake control module
• Removing/installing rear brake pad (When not pressing piston of rear brake caliper assembly)
• Removing/installing rear brake pad (When pressing piston of rear brake caliper assembly)
• Replacing rear brake pad
• Removing/installing rear brake caliper assembly
• Replacing rear brake caliper assembly
NOTE:
When the replaced rear brake pad, refer to
1.
PERFORM BRAKE OPERATION
With CONSULT
1.
Select “EHS/PKB”, “WORK SUPPORT”, and “BRAKE OPERATION” according to this order.
CAUTION:
• Never operate the parking brake switch.
• Never depress the brake pedal.
2.
Touch “START”.
>> GO TO 2.
2.
PERFORM BRAKE RELEASE
With CONSULT
1.
Select “EHS/PKB”, “WORK SUPPORT”, and “BRAKE RELEASE” according to this order.
CAUTION:
• Never operate the parking brake switch.
• Never depress the brake pedal.
Procedure
BRAKE OPERATION
Removing/installing electric parking brake control module
×
Replacing electric parking brake control module
×
Removing/installing rear brake pad (When not pressing piston of rear
brake caliper assembly)
×
Removing/installing rear brake pad (When pressing piston of rear brake
caliper assembly)
×
Replacing rear brake pad
×
Removing/installing rear brake caliper assembly
×
Replacing rear brake caliper assembly
×
Removing/installing parking brake switch
—
Replacing parking brake switch
—
Removing/installing clutch stroke sensor
—
Replacing clutch stroke sensor
—
Removing/installing clutch pedal
—
Replacing clutch pedal
—
RELEASE OF REAR BRAKE CALIPER
PB-57
< BASIC INSPECTION >
C
D
E
G
H
I
J
K
L
M
A
B
PB
N
O
P
RELEASE OF REAR BRAKE CALIPER
Description
INFOID:0000000010833871
CAUTION:
When the following operations are performed, always use CONSULT, for performing “BRAKE
RELEASE” of “WORK SUPPORT”.
×
: Required
—: not required
Work Procedure
INFOID:0000000010833872
CAUTION:
When the following operations are performed, always use CONSULT. (It cannot be performed by any
means other than CONSULT.)
• Removing/installing electric parking brake control module
• Replacing electric parking brake control module
• Removing/installing rear brake pad (When not pressing piston of rear brake caliper assembly)
• Removing/installing rear brake pad (When pressing piston of rear brake caliper assembly)
• Replacing rear brake pad
• Removing/installing rear brake caliper assembly
• Replacing rear brake caliper assembly
NOTE:
When the replaced rear brake pad, refer to
1.
PERFORM BRAKE OPERATION
With CONSULT
1.
Select “EHS/PKB”, “WORK SUPPORT”, and “BRAKE OPERATION” according to this order.
CAUTION:
• Never operate the parking brake switch.
• Never depress the brake pedal.
2.
Touch “START”.
>> GO TO 2.
2.
PERFORM BRAKE RELEASE
With CONSULT
1.
Select “EHS/PKB”, “WORK SUPPORT”, and “BRAKE RELEASE” according to this order.
CAUTION:
• Never operate the parking brake switch.
• Never depress the brake pedal.
Procedure
BRAKE RELEASE
Removing/installing electric parking brake control module
×
Replacing electric parking brake control module
×
Removing/installing rear brake pad (When not pressing piston of rear
brake caliper assembly)
×
Removing/installing rear brake pad (When pressing piston of rear brake
caliper assembly)
×
Replacing rear brake pad
×
Removing/installing rear brake caliper assembly
×
Replacing rear brake caliper assembly
×
Removing/installing parking brake switch
—
Replacing parking brake switch
—
Removing/installing clutch stroke sensor
—
Replacing clutch stroke sensor
—
Removing/installing clutch pedal
—
Replacing clutch pedal
—
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст