Nissan Qashqai J11. Manual — part 687
P0744 TORQUE CONVERTER
TM-323
< DTC/CIRCUIT DIAGNOSIS >
[CVT: RE0F10D]
C
E
F
G
H
I
J
K
L
M
A
B
TM
N
O
P
NO
>> INSPECTION END
Diagnosis Procedure
INFOID:0000000010589313
1.
CHECK INTERMITTENT INCIDNT
GI-41, "Intermittent Incident"
.
Is the inspection result normal?
YES
>> Replace transaxle assembly. Refer to
TM-415, "Removal and Installation"
.
NO
>> Repair or replace the malfunction items.
TM-324
< DTC/CIRCUIT DIAGNOSIS >
[CVT: RE0F10D]
P0746 PRESSURE CONTROL SOLENOID A
P0746 PRESSURE CONTROL SOLENOID A
DTC Logic
INFOID:0000000010589314
DTC DETECTION LOGIC
NOTE:
DC stands for "DRIVING CYCLE" and indicates a series of driving cycle of "Ignition switch OFF
→
ON
→
driv-
ing
→
OFF".
DTC CONFIRMATION PROCEDURE
CAUTION:
Be careful of the driving speed.
1.
PREPARATION BEFORE WORK
If another "DTC CONFIRMATION PROCEDURE" occurs just before, turn ignition switch OFF and wait for at
least 10 seconds, then perform the next test.
>> GO TO 2.
2.
CHECK DTC DETECTION
1.
Start the engine.
2.
Drive the vehicle.
3.
Maintain the following conditions for 10 seconds or more.
4.
Stop the vehicle.
5.
Check the first trip DTC.
Is “P0746”detected?
YES
>> Go to
DTC
CONSULT screen terms
(Trouble diagnosis content)
DTC detection condition
Possible causes
P0746
PC SOLENOID A
(Pressure Control Solenoid A
Performance/Stuck Off)
The detecting condition A or detection condi-
tion B is detected twice or more (1 second or
more later after detection of the first) in the
same DC under the following diagnosis condi-
tions:
• Diagnosis conditions
- Engine speed: More than 600 rpm
- Primary pulley speed: More than 450 rpm
- Idle is not being detected.
- Acceleration/deceleration speed:
−
0.49 m/
s
2
(
−
0.05 G) or more
- The primary pulley speed experienced 300
rpm or more and the secondary pulley
speed experienced 250 rpm or more at least
once.
- Secondary pulley speed: More than 150
rpm
- TCM power supply voltage: More than 11 V
• Detection condition A
- Status with the shifting ratio of the primary
pulley speed/secondary pulley ratio exceed-
ing 2.981 is 0.2 sec. or more continuously.
• Detection condition B
- Status with the shifting ratio of the primary
pulley speed/secondary pulley ratio exceed-
ing 3.781 is 0.1 sec. or more continuously.
• Line pressure solenoid valve
• Control valve assembly
Selector lever
: “D” position
Accelerator pedal position
: 0.5/8 or more
Vehicle speed
: 40 km/h (25 MPH) or more
P0746 PRESSURE CONTROL SOLENOID A
TM-325
< DTC/CIRCUIT DIAGNOSIS >
[CVT: RE0F10D]
C
E
F
G
H
I
J
K
L
M
A
B
TM
N
O
P
NO
>> INSPECTION END
Diagnosis Procedure
INFOID:0000000010589315
1.
CHECK INTERMITTENT INCIDNT
GI-41, "Intermittent Incident"
.
Is the inspection result normal?
YES
>> Replace transaxle assembly. Refer to
TM-415, "Removal and Installation"
.
NO
>> Repair or replace the malfunction items.
TM-326
< DTC/CIRCUIT DIAGNOSIS >
[CVT: RE0F10D]
P0776 PRESSURE CONTROL SOLENOID B
P0776 PRESSURE CONTROL SOLENOID B
DTC Logic
INFOID:0000000010589316
DTC DETECTION LOGIC
DTC
CONSULT screen terms
(Trouble diagnosis content)
DTC detection condition
Possible cause
P0776
PC SOLENOID B
(Pressure Control Solenoid
“B” Performance/Stuck Off)
When any of 1 or 2 is satisfied and this state
is maintained for 10 seconds:
1.
When all of the following conditions are
satisfied:
-
DTC other than the applicable DTC is
not detected.
-
Engine speed: More than 625 rpm
-
Selector lever: Other than P/N position
-
CVT fluid temperature: More than -
20
°
C (-4
°
F)
-
TCM power supply: More than 11 V
-
The difference between instruction
pressure of secondary pressure and
10-msec-ago instruction secondary
pressure is 0 MPa or more
-
Instruction pressure of secondary
pressure: 0 MPa or more
-
Instruction pressure of secondary
pressure - secondary pressure: More
than 1.2 MPa
-
When all of the following conditions are
satisfied and this state is maintained
for 1.52 seconds:
•
DTC other than the applicable DTC is
not detected.
•
CVT fluid temperature: More than -
20
°
C (-4
°
F)
•
Selector lever: Other than P/N position
•
Instruction pressure of secondary
pressure
−
secondary pressure: 0.25
MPa or more
2.
When all of the following conditions are
satisfied:
-
DTC other than the applicable DTC is
not detected.
-
CVT fluid temperature: More than -
20
°
C (-4
°
F)
-
Selector lever: Other than P/N position
-
TCM power supply: More than 11 V
-
When all of the following conditions are
satisfied and this state is maintained
for 5.5 seconds:
•
DTC other than the applicable DTC is
not detected.
•
CVT fluid temperature: More than -
20
°
C (-4
°
F)
•
Selector lever: Other than P/N position
•
Secondary pressure - instruction pres-
sure of secondary pressure: 1.2 MPa
or more
-
The difference between instruction
pressure of secondary pressure and
10-msec-ago instruction secondary
pressure is 0 MPa or more
-
Secondary pressure - instruction pres-
sure of secondary pressure: More than
1.2 MPa
Secondary pressure solenoid valve
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст