Nissan Qashqai J11. Manual — part 85
AIR CLEANER AND AIR DUCT
EM-279
< REMOVAL AND INSTALLATION >
[K9K]
C
D
E
F
G
H
I
J
K
L
M
A
EM
N
P
O
AIR CLEANER AND AIR DUCT
Exploded View
INFOID:0000000010478308
Removal and Installation
INFOID:0000000010282060
REMOVAL
1.
Remove air duct (air cleaner side).
2.
Remove air duct (inlet side).
3.
Disconnect mass air flow sensor.
4.
Disconnect air hose from air cleaner filter unit.
5.
Remove air cleaner filter unit.
6.
Remove air hose.
7.
Remove air filter element if necessary.
INSTALLATION
• Install in the reverse order of removal.
Inspection
INFOID:0000000010287198
INSPECTION AFTER REMOVAL
1.
Clip
2.
Air duct (inlet side)
3.
Air duct (air cleaner side)
4.
Holder
5.
Air filter element
6.
Air cleaner filter unit
7.
Mass air flow sensor
8.
Air hose
9.
Mounting rubber
10. Air cleaner filter unit bracket
E1BIA1158GB
EM-280
< REMOVAL AND INSTALLATION >
[K9K]
AIR CLEANER AND AIR DUCT
Inspect air ducts, air cleaner and hose for crack or tear.
• If anything found, replace air duct and resonator assembly.
CHARGE AIR COOLER
EM-281
< REMOVAL AND INSTALLATION >
[K9K]
C
D
E
F
G
H
I
J
K
L
M
A
EM
N
P
O
CHARGE AIR COOLER
Exploded View
INFOID:0000000010287199
for symbols description.
Removal and Installation
INFOID:0000000010282062
REMOVAL
Air inlet hose and tube.
1.
Remove engine cover.
2.
Remove air inlet hose and tube. Refer to
Charge air cooler.
1.
Remove front bumper. Refer to
EXT-19, "Removal and Installation"
1.
Turbocharger
2.
Electric throttle control actuator
3.
Air inlet tube
4.
Cooling fan
5.
Charge air cooler
6.
High pressure pump
7.
Air inlet hose
E1BIA1152GB
EM-282
< REMOVAL AND INSTALLATION >
[K9K]
CHARGE AIR COOLER
2.
Put aside front bumper reinforcement (1) with harness assem-
bly.
3.
Remove:
• Radiator air guide RH (1).
• Radiator air guide LH (2).
• Radiator air guide lower (3).
• Radiator bracket mounting upper (4)
4.
Put aside radiator core support upper. Refer to
DLK-155, "HRA2DDT : Removal and Installation"
(Type 1),
DLK-336, "K9K : Removal and Installation"
(Type 2),
DLK-467, "K9K : Removal and Installation"
(Type 3),
DLK-605, "K9K : Removal and Installation"
(Type 4).
5.
Unhook and rotate charge air cooler (1).
6.
Remove charge air cooler.
CAUTION:
• Avoid interference between the charge air cooler and radiator.
• When removing charge air cooler, close opening on turbo
charger and intake manifold with shop cloth or other suitable
material.
INSTALLATION
1.
When replacing the electric throttle control actuator, this procedure must be performed. Refer to
"Special Repair Requirement List"
.
Install in the reverse order of removal paying attention to the following points:
• Apply a neutral detergent (fluid) to the joint between hoses and pipes (oil is not permissible).
• Pay attention to identification mark and direction.
• When installing air inlet hoses and tubes. Refer to
.
E1BIA1038ZZ
E1BIA1037ZZ
E1BIA1039ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст