Nissan Qashqai J11. Manual — part 641
PREPARATION
TM-139
< PREPARATION >
[6MT: RS6F52A]
C
E
F
G
H
I
J
K
L
M
A
B
TM
N
O
P
Puller
Removing each bearing, gear, and bushing
Puller
Removing each bearing, gear, and bushing
Tool name
Description
ZZA0537D
NT077
TM-140
< PERIODIC MAINTENANCE >
[6MT: RS6F52A]
GEAR OIL
PERIODIC MAINTENANCE
GEAR OIL
4WD
4WD : Exploded View
INFOID:0000000010288498
4WD : Draining
INFOID:0000000010288499
1.
Start engine and let it run to warm up transaxle.
2.
Stop engine. Remove drain plug and then drain gear oil.
3.
Set a gasket on drain plug and install it to clutch housing.
Tighten drain plug to the specified torque.
CAUTION:
Never reuse gasket.
4WD : Refilling
INFOID:0000000010288500
1.
Remove filler plug (1). Fill with new gear oil to transaxle.
2.
After refilling gear oil, check oil level. Refer to
.
3.
Set a gasket on filler plug and then install it to transaxle case.
CAUTION:
Never reuse gasket.
4.
Tighten filler plug to the specified torque.
4WD : Inspection
INFOID:0000000010288501
LEAKAGE
Make sure that gear oil is not leaking from transaxle or around it.
LEVEL
JPDIC0073ZZ
A
: Suitable gauge
: Vehicle front
Oil grade and viscosity
: Refer to
.
Oil capacity (reference)
: Refer to
JPDIC0139ZZ
GEAR OIL
TM-141
< PERIODIC MAINTENANCE >
[6MT: RS6F52A]
C
E
F
G
H
I
J
K
L
M
A
B
TM
N
O
P
1.
Remove filler plug (1).
2.
Measure oil level using a suitable gauge (A) as shown in the fig-
ure and then check if it is within the specifications.
CAUTION:
• Never start engine while checking oil level.
• Measure suitable gauge according to the wall of the plug
mounting hole.
3.
Set a gasket on filler plug and then install it to transaxle case.
CAUTION:
Never reuse gasket.
4.
Tighten filler plug to the specified torque.
: Vehicle front
Oil level “L”
: Refer to
JPDIC0139ZZ
TM-142
< REMOVAL AND INSTALLATION >
[6MT: RS6F52A]
SIDE OIL SEAL
REMOVAL AND INSTALLATION
SIDE OIL SEAL
Exploded View
INFOID:0000000010288502
Removal and Installation
INFOID:0000000010288503
REMOVAL
1.
Remove front drive shafts. Refer to
FAX-22, "Removal and Installation (LH)"
"Removal and Installation (RH)"
(4WD).
2.
Remove differential side oil seals using a suitable tool.
CAUTION:
Never damage transaxle case and clutch housing.
INSTALLATION
Note the following, and install in the reverse order of removal.
• Install differential side oil seal to transaxle case and clutch housing
using the drift.
CAUTION:
• Never reuse differential side oil seal.
• When installing, never incline differential side oil seal.
• Never damage clutch housing and transaxle case.
• Check oil level and oil leakage after installation. Refer to
SCIA0824E
Dimension “A”
: -0.5 - 0.5 mm (-0.020 - 0.020 in)
Transaxle case side
: Drift [SST: ST30720000]
Clutch housing side
: Drift [SST: ST33400001]
SCIA1010E
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст