Nissan Qashqai J11. Manual — part 19
PREPARATION
EM-15
< PREPARATION >
[HRA2DDT]
C
D
E
F
G
H
I
J
K
L
M
A
EM
N
P
O
Oxygen sensor thread cleaner
Reconditioning the exhaust system threads
before installing a new heated oxygen sensor
(Use with anti-seize lubricant shown below.)
a = 18 mm (0.71 in) dia. for zirconia heated
oxygen sensor
b = 12 mm (0.47 in) dia. for titania heated
oxygen sensor
Acoustic tension gauge
Checking drive belt tension
Anti-seize lubricant (Permatex 133AR
or equivalent meeting MIL specifica-
tion MIL-A-907)
Lubricating oxygen sensor thread cleaning
tool when reconditioning exhaust system
threads
Manual lift table caddy
Removing and installing engine
Tube presser
Pressing the tube of liquid gasket
Tool name
Description
AEM488
PBIC3881E
AEM489
ZZA1210D
S-NT052
EM-16
< PERIODIC MAINTENANCE >
[HRA2DDT]
DRIVE BELT
PERIODIC MAINTENANCE
DRIVE BELT
Exploded View
INFOID:0000000010282201
for symbols in the figure.
Checking
INFOID:0000000010282202
CAUTION:
• Replace the drive belt that has been removed with a new one.
• Drive belt auto-tensioner, idler pulley and idler roller must be replaced with new ones when the drive
belt is replaced.
• Never run the engine without the drive belt to avoid damaging the crankshaft pulley.
Tension Adjustment
INFOID:0000000010282203
Removal and Installation
INFOID:0000000010282204
CAUTION:
• Replace the drive belt that has been removed with a new one.
• Drive belt auto-tensioner and idler pulley must be replaced with new ones when the drive belt is
replaced.
• Never run the engine without the drive belt to avoid damaging the crankshaft pulley.
REMOVAL
1.
Remove front fender protector (RH). Refer to
E1BIA1001GB
1.
Alternator
2.
Drive belt
3.
Water pump
4.
Idler roller
5.
Idler pulley
6.
A/C Compressor
7.
Drive belt auto-tensioner
DRIVE BELT
EM-17
< PERIODIC MAINTENANCE >
[HRA2DDT]
C
D
E
F
G
H
I
J
K
L
M
A
EM
N
P
O
2.
Release the tension on the drive belt by turning drive belt auto-
tensioner (1) clockwise using a 16mm (0.63 in) socket and hold
drive belt auto-tensioner to this position.
3.
Remove drive belt.
4.
Release the drive belt auto-tensioner until normal position.
CAUTION:
• Clean with a brush the v-block of the crankshaft pulley to remove all dust.
INSTALLATION
1.
Rotate drive belt auto-tensioner clockwise using a 16mm (0.63 in) socket and hold it.
2.
Install drive belt.
CAUTION:
• Check that drive belt is completely set to pulleys.
• Check for engine oil, working fluid and engine coolant are not adhered to drive belt and each pulley
groove.
3.
Release the drive belt auto-tensioner until drive belt tension is apply.
4.
Turn crankshaft clockwise twice to set drive belt tension on all pulleys.
5.
Install in the reverse order of removal.
E1BIA1000ZZ
EM-18
< PERIODIC MAINTENANCE >
[HRA2DDT]
AIR CLEANER FILTER
AIR CLEANER FILTER
Removal and Installation
INFOID:0000000010282205
REMOVAL
1.
Press the points (A) to separate air resonator from air duct and
air cleaner filter unit.
2.
Remove air resonator following the arrow.
3.
Unhook clips (1) on the air cleaner filter holder.
E1BIA1002ZZ
E1BIA1003ZZ
E1BIA1004ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст