Nissan Qashqai J11. Manual — part 18
PRECAUTIONS
EM-11
< PRECAUTION >
[HRA2DDT]
C
D
E
F
G
H
I
J
K
L
M
A
EM
N
P
O
• The auto acc function is adapted to this vehicle. For this reason, even when the ignition switch is turned
to OFF position, the accessory power source does not turned OFF and continues to be supplied for a
certain amount of time.
6.
Disconnect both battery cables. The steering lock will remain released with both battery cables discon-
nected and the steering wheel can be turned.
7.
Perform the necessary repair operation.
8.
When the repair work is completed, re-connect both battery cables. With the brake pedal released, turn
the ignition switch from OFF position to ON position, then to LOCK position. (The steering wheel will lock
when the ignition switch is turned to LOCK position.)
9.
Perform self-diagnosis check of all control units using CONSULT.
Liquid Gasket
INFOID:0000000010282198
REMOVAL OF LIQUID GASKET
• After removing the mounting bolts and nuts, separate the mating
surface using seal cutter (SST) and remove the old liquid gasket
sealing.
CAUTION:
Be careful not to damage the mating surfaces.
• Tap seal cutter to insert it (1), and then slide it (2) by tapping on the
side as shown in the figure.
• In areas where seal cutter is difficult to use, use plastic hammer to
lightly tap the parts, to remove it.
CAUTION:
If for some unavoidable reason tool such as screwdriver is
used, be careful not to damage the mating surfaces.
LIQUID GASKET APPLICATION PROCEDURE
1.
Using a scraper, remove the old liquid gasket adhering to the liq-
uid gasket application surface and the mating surface.
• Remove the liquid gasket completely from the groove of the
liquid gasket application surface, mounting bolts and bolt
holes.
2.
Wipe the liquid gasket application surface and the mating sur-
face with white gasoline (lighting and heating use) to remove
adhering moisture, grease and foreign materials.
3.
Attach liquid gasket tube to the tube presser (commercial ser-
vice tool).
Use Genuine Liquid Gasket or equivalent.
4.
Apply the liquid gasket without breaks to the specified location
with the specified dimensions.
• If there is a groove for the liquid gasket application, apply the
liquid gasket to the groove.
PBIC0275E
PBIC0003E
EMA0622D
EM-12
< PRECAUTION >
[HRA2DDT]
PRECAUTIONS
• As for the bolt holes, normally apply the liquid gasket inside
the holes. Occasionally, it should be applied outside the holes.
Make sure to read the text of service manual.
• Within 5 minutes of liquid gasket application, install the mating
component.
• If the liquid gasket protrudes, wipe it off immediately.
• Do not retighten mounting bolts or nut after the installation.
• Wait 30 minutes or more after installation before refilling
engine oil and engine coolant.
CAUTION:
If there are specific instructions in this manual, observe
them.
SEM159F
PREPARATION
EM-13
< PREPARATION >
[HRA2DDT]
C
D
E
F
G
H
I
J
K
L
M
A
EM
N
P
O
PREPARATION
PREPARATION
Special Service Tools
INFOID:0000000010282199
NISSAN tool number
(RENAULT tool number)
Tool name
Description
KV10111100
( — )
Seal cutter
Removing oil pan (lower and upper) etc.
KV113E0010
(Mot.1566)
Fuel tube adapter
Tool for removing fuel tube
KV10112100
( — )
Angle wrench
Tightening bolts for bearing cap, cylinder
head, etc. in angle
KV10117100
( — )
Heated oxygen sensor wrench
Loosening or tightening heated oxygen sen-
sor 1
For 22 mm (0.87 in) width hexagon nut
—
(Mot.1533)
Injector seal fitter
Tool for installing injector seal
—
(Mot.1431)
Flywheel locking tool
To lock flywheel
S-NT046
MBIB0379E
S-NT014
NT379
E1BIA1170ZZ
JMAIA0431ZZ
EM-14
< PREPARATION >
[HRA2DDT]
PREPARATION
Commercial Service Tools
INFOID:0000000010282200
EM03470000
( — )
Piston ring compressor
Installing piston assembly into cylinder bore
KV113B0180
(Mot.1511)
Valve seal drift
Tool for installing valve stem seals
Quick connector release
Removing fuel tube quick connectors in en-
gine room
(Available in SEC. 164 of PARTS CATALOG:
Part No. 16441 6N210)
KV113B0090
(Mot.1335)
Valve seal remover
Tool for removing valve stem seals
NISSAN tool number
(RENAULT tool number)
Tool name
Description
S-NT044
MBIB0378E
PBIC0198E
MBIB0370E
Tool name
Description
Spark plug wrench
Removing and installing spark plug
Piston ring expander
Removing and installing piston ring
PBIC3874E
S-NT030
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст