Nissan Qashqai J11. Manual — part 837
FRONT DRIVE SHAFT
FAX-35
< UNIT DISASSEMBLY AND ASSEMBLY >
[2WD]
C
E
F
G
H
I
J
K
L
M
A
B
FAX
N
O
P
2.
Remove snap ring (1).
3.
Press out support bearing from housing.
4.
Remove dust shield.
Wheel Side
1.
Fix shaft with a vise.
CAUTION:
Protect shaft using aluminum or copper plates when fixing with a vise.
2.
Remove boot bands, and then remove boot from joint sub-assembly.
3.
Screw the drive shaft puller (A) 30 mm (1.18 in) or more into the
thread of joint sub-assembly, and pull joint sub-assembly with a
sliding hammer (B) from shaft.
CAUTION:
• If joint sub-assembly cannot be removed after five or
more unsuccessful attempts, replace shaft and joint sub
assembly as a set.
• Align sliding hammer and drive shaft and remove them by
pulling forcibly.
4.
Remove circular clip from shaft.
5.
Remove boot from shaft.
6.
Clean old grease on joint sub-assembly with paper waste while
rotating ball cage.
ASSEMBLY
Transaxle Assembly Side
1.
Wrap serration on shaft with tape (A) to protect boot from dam-
age. Install new boot and boot bands to shaft.
CAUTION:
Never reuse boot and boot band.
2.
Remove the tape wrapped around the serration on shaft.
JPDIF0106ZZ
YAX004
JPDIF0015ZZ
JPDIF0009ZZ
FAX-36
< UNIT DISASSEMBLY AND ASSEMBLY >
[2WD]
FRONT DRIVE SHAFT
Secure dynamic damper with bands in the following specified posi-
tion when removing.
CAUTION:
Never reuse bands.
Wheel Side
For further details, refer to the installation procedure of “
FAX-18, "WHEEL SIDE : Removal and Installation"
for the drive shaft boot.
Inspection
INFOID:0000000011722645
INSPECTION AFTER REMOVAL
• Move joint up/down, left/right, and in the axial directions. Check for motion that is not smooth and for signifi-
cant looseness.
• Check boot for cracks, damage, and leakage of grease.
• Disassemble drive shaft and exchange malfunctioning part if there
is any non-standard condition.
INSPECTION AFTER DISASSEMBLY
Shaft
Check shaft for runout, cracks, or other damage. Replace if there are.
Dynamic Damper
Check damper for cracks or wear. Replace if necessary.
Joint Sub-Assembly (Wheel Side)
Check the following:
• Joint sub-assembly for rough rotation and excessive axial looseness
• The inside of the joint sub-assembly for entry of foreign material
• Joint sub-assembly for compression scars, cracks, and fractures inside of joint sub-assembly
Replace joint sub-assembly if there are any non-standard conditions of components.
Housing and Spider assembly (Transaxle Side)
Replace housing and spider assembly if there is any scratching or wear of housing on roller contact surface or
spider roller contact surface.
NOTE:
Housing and spider assembly are used in a set.
Support Bearing (Right Side)
Make sure wheel bearing rolls freely and is free from noise, cracks, pitting or wear. Replace support bearing if
there are any non-standard conditions.
Support Bearing Bracket (Right Side)
Check for bending, cracks, or damage. Replace support bearing bracket if there are any non-standard condi-
tions.
Standard
.
FAC0156D
SDIA1190J
SERVICE DATA AND SPECIFICATIONS (SDS)
FAX-37
< SERVICE DATA AND SPECIFICATIONS (SDS)
[2WD]
C
E
F
G
H
I
J
K
L
M
A
B
FAX
N
O
P
SERVICE DATA AND SPECIFICATIONS (SDS)
SERVICE DATA AND SPECIFICATIONS (SDS)
Wheel Bearing
INFOID:0000000010297322
Drive Shaft
INFOID:0000000010436944
HRA2DDT
M/T models
MR20DD
M/T models
Item
Standard
Axial end play
0.0 mm (0.0 in)
Rotating torque
1.9 N.m (0.19 kg-m, 17 in-lb) or less
Spring balance measurement
13.7 N (1.40 kg-f, 3.08 lb-f) or less
Joint
Wheel side
Transaxle assembly side
Grease quantity
Left side
100 – 120 g (3.53 – 4.23 oz)
155 – 175 g (5.47 – 6.17 oz)
Right side
Boots installed length (L)
Left side
131 mm (5.16 in)
180.4 mm (7.10 in)
Right side
172.4 mm (6.79 in)
Dynamic damper
A
B
Dimension
Left side
287 – 291 mm (11.30 – 11.46 in)
70 mm (2.76 in)
Right side
JPDIF0031ZZ
FAC0156D
FAX-38
< SERVICE DATA AND SPECIFICATIONS (SDS)
[2WD]
SERVICE DATA AND SPECIFICATIONS (SDS)
SERVICE DATA AND SPECIFICATIONS (SDS)
SERVICE DATA AND SPECIFICATIONS (SDS)
Wheel Bearing
INFOID:0000000010297322
Drive Shaft
INFOID:0000000010436944
HRA2DDT
M/T models
MR20DD
M/T models
Item
Standard
Axial end play
0.0 mm (0.0 in)
Rotating torque
1.9 N.m (0.19 kg-m, 17 in-lb) or less
Spring balance measurement
13.7 N (1.40 kg-f, 3.08 lb-f) or less
Joint
Wheel side
Transaxle assembly side
Grease quantity
Left side
100 – 120 g (3.53 – 4.23 oz)
155 – 175 g (5.47 – 6.17 oz)
Right side
Boots installed length (L)
Left side
131 mm (5.16 in)
180.4 mm (7.10 in)
Right side
172.4 mm (6.79 in)
Dynamic damper
A
B
Dimension
Left side
287 – 291 mm (11.30 – 11.46 in)
70 mm (2.76 in)
Right side
JPDIF0031ZZ
FAC0156D
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст