Nissan Qashqai J11. Manual — part 836
FRONT DRIVE SHAFT
FAX-31
< UNIT DISASSEMBLY AND ASSEMBLY >
[2WD]
C
E
F
G
H
I
J
K
L
M
A
B
FAX
N
O
P
UNIT DISASSEMBLY AND ASSEMBLY
FRONT DRIVE SHAFT
Exploded View
INFOID:0000000010435861
LHD models
RHD models - HRA2DDT, MR20DD, K9K, MR16DDT
JPDIF0047ZZ
1.
Circular clip
2.
Dust shield
3.
Housing
4.
Snap ring
5.
Spider assembly
6.
Stopper ring
7.
Boot band
8.
Boot
9.
Shaft
10. Damper band
11.
Dynamic damper
12. Circular clip
13. Joint sub-assembly
Wheel side
Refer to
JPDIF0045ZZ
1.
Joint sub-assembly
2.
Circular clip
3.
Boot band
4.
Boot
5.
Shaft
6.
Damper band
7.
Dynamic damper
8.
Stopper ring
9.
Spider assembly
10. Snap ring
11.
Housing assembly
12. Dust shield
FAX-32
< UNIT DISASSEMBLY AND ASSEMBLY >
[2WD]
FRONT DRIVE SHAFT
RHD models - R9M
Disassembly and Assembly
INFOID:0000000011722644
DISASSEMBLY
Transaxle Side
1.
Housing on the side of transaxle cannot be disassembled. When removing boot, perform procedure 1 to 5
on the wheel side first. And then remove dynamic damper and band (left side).
2.
Remove boot bands, then remove boots from housing assembly, and remove boot from shaft after the
above service.
3.
Remove dust shield from housing assembly.
4.
Remove circular clip from housing assembly (left side).
5.
Clean old grease on housing assembly with paper towels.
Support Bearing
13. Support bearing
14. Snap ring
15. Dust shield
: Wheel side
Refer to
for symbols in the figure.
AWDIA1159ZZ
1.
Joint sub-assembly
2.
Circular clip
3.
Boot band
4.
Boot
5.
Shaft
6.
Stopper ring
7.
Spider assembly
8.
Snap ring
9.
Housing assembly
10. Dust shield
11.
Support bearing
12. Plate
13. Support bearing bracket
: Wheel side
Refer to
for symbols in the figure.
FRONT DRIVE SHAFT
FAX-33
< UNIT DISASSEMBLY AND ASSEMBLY >
[2WD]
C
E
F
G
H
I
J
K
L
M
A
B
FAX
N
O
P
Exploded View (RH)
INFOID:0000000010435863
HRA2DDT, MR20DD, K9K
R9M
JPDIF0045ZZ
1.
Joint sub-assembly
2.
Circular clip
3.
Boot band
4.
Boot
5.
Shaft
6.
Damper band
7.
Dynamic damper
8.
Stopper ring
9.
Spider assembly
10. Snap ring
11.
Housing assembly
12. Dust shield
13. Support bearing
14. Snap ring
15. Dust shield
: Wheel side
Refer to
AWDIA1159ZZ
FAX-34
< UNIT DISASSEMBLY AND ASSEMBLY >
[2WD]
FRONT DRIVE SHAFT
3.
Screw the drive shaft puller (A) 30 mm (1.18 in) or more into the
thread of joint sub-assembly, and pull joint sub-assembly with a
sliding hammer (B) from shaft.
CAUTION:
• If joint sub-assembly cannot be removed after five or
more unsuccessful attempts, replace shaft and joint sub
assembly as a set.
• Align sliding hammer and drive shaft and remove them by
pulling directory.
4.
Remove circular clip from shaft.
5.
Remove boot from shaft.
6.
Clean old grease on joint sub-assembly with paper towels while
rotating ball cage.
ASSEMBLY
Transaxle Assembly Side
1.
Wrap serration on housing assembly with tape to protect boot from damage. Install new boot and boot
bands to housing assembly.
CAUTION:
Never reuse boot and boot band.
2.
Remove the tape wrapped around the serration on housing assembly.
3.
Apply specified amount grease to the housing assembly.
4.
Install boot securely into grooves (indicated by “*” marks) shown
in the figure.
CAUTION:
If grease adheres to the boot mounting surface (with “*”
mark) on shaft or housing, boot may be removed. Remove
all grease from the surface.
5.
To prevent from deformation of the boot, adjust the boot installa-
tion length to the value shown below (L) by inserting the suitable
tool into the inside of boot from the large diameter side of boot
and discharging inside air.
CAUTION:
• If the boot installation length exceeds the standard, it may cause breakage in boot.
• Be careful not to touch the inside of the boot with the tip of tool.
6.
Install new larger and smaller boot bands securely.
CAUTION:
Never reuse boot band.
7.
Put boot band in the groove on drive shaft boot. Then fit pawls
(
) into holes to temporary installation.
NOTE:
For the large diameter side, fit projection (A) and guide slit (B) at
first.
JPDIF0015ZZ
Standard
Grease amount
: Refer to
Standard
Boots installed
length (L)
: Refer to
JPDIF0032ZZ
SDIA3557E
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст