Nissan Qashqai J11. Manual — part 1798
W W - 7 0
< SYMPTOM DIAGNOSIS >
WIPER AND WASHER SYSTEM SYMPTOMS
Front wiper does not
operate normally
Intermittent adjust-
ment cannot be per-
formed
• Combination switch
• Harness between combination switch and BCM
• BCM
.
BCM
—
Intermittent control
linked with vehicle
speed cannot be per-
formed
Check the wiper setting is linked with vehicle speed.
Refer to
WW-23, "WIPER : CONSULT Function - WIPER"
.
Wiper is not linked to
the washer operation
• Combination switch
• Harness between combination switch and BCM
• BCM
.
BCM
—
Does not return to
stop position [Re-
peatedly operates for
10 seconds and then
stops for 20 seconds.
After that, it stops the
operation. (Fail-
safe)]
• IPDM E/R
• Harness between IPDM E/R and front wiper
motor
• Front wiper motor
Front wiper stop position sig-
nal circuit
Refer to
Rear wiper does not
operate
ON only
• Combination switch
• Harness between combination switch and BCM
• BCM
.
INT only
• Combination switch
• Harness between combination switch and BCM
• BCM
.
ON and INT
• Combination switch
• Harness between combination switch and BCM
• BCM
.
• BCM
• Harness between rear wiper motor and BCM
• Harness between rear wiper motor and ground
• Rear wiper motor
Rear wiper motor circuit
Refer to
Rear wiper does not
stop
ON only
• Combination switch
• BCM
.
INT only
• Combination switch
• BCM
.
Rear wiper does not
operate normally
Wiper is not linked to
the washer operation
• Combination switch
• Harness between rear wiper motor and BCM
• BCM
.
BCM
—
Rear wiper does not
return to the stop po-
sition. [Stops after a
five-second opera-
tion. (Fail-safe)]
• BCM
• Harness between rear wiper motor and BCM
• Rear wiper motor
Rear wiper stop position sig-
nal circuit
Refer to
Rear wiper does not
operate even when
shift position is “R”.
Reverse switch signal (CAN communication)
• BCM
• IPDM E/R
BCM DATA MONITOR
“REVERSE SIGNAL - IPDM”
Symptom
Probable malfunction location
Inspection item
WIPER AND WASHER SYSTEM SYMPTOMS
WW-71
< SYMPTOM DIAGNOSIS >
C
D
E
F
G
H
I
J
K
M
A
B
WW
N
O
P
Headlamp washer
does not operate.
Headlamp washer
does not operate
when headlamps are
turned ON.
• Harness between headlamp washer switch and
BCM
• Harness between headlamp washer switch and
ground
• Headlamp washer switch
• BCM
Headlamp washer switch
Refer to
• Combination switch
• Harness between combination switch and BCM
• BCM
Combination switch
Refer to
.
• Fusible link
• Harness between fusible link and headlamp
washer relay
• Headlamp washer relay
• Harness between headlamp washer relay and
IPDM E/R
• IPDM E/R
• Harness between headlamp washer relay and
headlamp washer pump
• Harness between headlamp washer pump and
ground
• Headlamp washer pump
Headlamp washer circuit
Refer to
BCM
—
Symptom
Probable malfunction location
Inspection item
WW-72
< SYMPTOM DIAGNOSIS >
NORMAL OPERATING CONDITION
NORMAL OPERATING CONDITION
Description
INFOID:0000000010430989
FRONT WIPER MOTOR PROTECTION FUNCTION
• IPDM E/R may stop the front wiper to protect the front wiper motor if any obstruction (operation resistance)
such as a large amount of snow is detected during the front wiper operation.
• At that time turn OFF the front wiper and remove the foreign object. Then reactivate the front wiper. The
wiper will operate normally.
REAR WIPER MOTOR PROTECTION FUNCTION
• BCM may stop rear wiper to protect the rear wiper motor when the rear wiper is stopped for 5 seconds or
more due to a snowfall.
• Rear wiper operates normally 1 minute after the obstacles are removed with rear wiper OFF.
FRONT WIPER DOES NOT OPERATE
WW-73
< SYMPTOM DIAGNOSIS >
C
D
E
F
G
H
I
J
K
M
A
B
WW
N
O
P
FRONT WIPER DOES NOT OPERATE
Description
INFOID:0000000010430990
The front wiper does not operate under any operation conditions.
Diagnosis Procedure
INFOID:0000000010430991
1.
CHECK WIPER RELAY OPERATION
CONSULT ACTIVE TEST
1.
Select “FRONT WIPER” of IPDM E/R active test item.
2.
With operating the test item, check front wiper operation.
Is front wiper operation normally?
YES
>> GO TO 4.
NO
>> GO TO 2.
2.
CHECK FRONT WIPER MOTOR FUSE
1.
Turn ignition switch OFF.
2.
Check that the following fuse is not fusing.
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> Replace the fuse after repairing the applicable circuit.
3.
CHECK FRONT WIPER MOTOR GROUND CIRCUIT
Check front wiper motor ground circuit. Refer to
Is the inspection result normal?
YES
>> GO TO 4.
NO
>> Repair or replace harness.
4.
CHECK FRONT WIPER REQUEST SIGNAL INPUT
CONSULT DATA MONITOR
1.
Select “FR WIP REQ” of IPDM E/R data monitor item.
2.
Switch the front wiper switch to HI and LO.
3.
With operating the front wiper switch, check the status of “FR WIP REQ”.
Is the inspection result normal?
YES
>> Replace IPDM E/R. Refer to
PCS-67, "Removal and Installation"
.
NO
>> GO TO 5.
5.
CHECK COMBINATION SWITCH
Perform the inspection of the combination switch. Refer to
Is combination switch normal?
LOW
: Front wiper LO operation
HIGH
: Front wiper HI operation
OFF
: Stop the front wiper.
Unit
Location
No.
Capacity
Front wiper motor
IPDM E/R
60
30 A
Monitor item
Condition
Monitor status
FR WIP REQ
Front wiper switch
HI
HIGH
LO
LOW
INT
OFF
STOP
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст