Nissan Qashqai J11. Manual — part 2212
DAS-262
< DTC/CIRCUIT DIAGNOSIS >
[CHASSIS CONTROL]
C1BB5-00 IGNITION POWER SUPPLY
NO
>> INSPECTION END
3.
CHECK FUSE
1.
Turn the ignition switch OFF.
2.
Check that any of the following fuse is not fusing.
Is the inspection result normal?
YES
>> GO TO 4.
NO
>> Repair the applicable circuit. And then replace the fuse.
4.
CHECK CHASSIS CONTROL MODULE IGNITION POWER SUPPLY
1.
Disconnect chassis control module harness connector.
2.
Check the voltage between chassis control module harness connector and ground.
Is the inspection result normal?
YES
>> GO TO 5.
NO
>> Repair or replace harness.
5.
CHECK CHASSIS CONTROL MODULE GROUND CIRCUIT
1.
Turn the ignition switch OFF.
2.
Check the continuity between chassis control module harness connector and ground.
Is the inspection result normal?
YES
>> GO TO 6.
NO
>> Repair or replace harness.
6.
PERFORM SELF-DIAGNOSIS 2
1.
Connect chassis control module harness connector.
2.
Perform “Self Diagnostic Result” for “CHASSIS CONTROL”.
Is DTC “C1BB5-00” detected?
YES
>> Replace the chassis control module. Refer to
DAS-312, "Removal and Installation"
.
NO
>> INSPECTION END
Signal name
Fuse No.
Ignition power supply
4 (10A)
Chassis control module
Ignition switch
—
Voltage
Connector
Terminal
M43
10
OFF
Ground
Approx. 0 V
ON
6.4 – 16 V
Chassis control module
—
Continuity
Connector
Terminal
M43
12
Ground
Existed
DAS
C1BB6-00 IGNITION POWER SUPPLY
DAS-263
< DTC/CIRCUIT DIAGNOSIS >
[CHASSIS CONTROL]
C
D
E
F
G
H
I
J
K
L
M
B
N
P
A
C1BB6-00 IGNITION POWER SUPPLY
DTC Description
INFOID:0000000010417011
DTC DETECTION LOGIC
POSSIBLE CAUSE
• Harness or connector
• Fuse
• Ignition power supply system
• Battery
• Chassis control module
DTC CONFIRMATION PROCEDURE
1.
PRECONDITIONING
If “DTC CONFIRMATION PROCEDURE” has been previously conducted, always turn the ignition switch OFF
and wait at least 10 seconds before conducting the next test.
>> GO TO 2.
2.
CHECK DTC DETECTION
With CONSULT
1.
Turn the ignition switch OFF to ON.
CAUTION:
Be sure to wait of 10 seconds after turning ignition switch OFF or ON.
2.
Perform “Self Diagnostic Result” for “CHASSIS CONTROL”.
Is DTC “C1BB6-00” detected?
YES
>> Proceed to
DAS-263, "Diagnosis Procedure"
NO-1
>> To check malfunction symptom before repair: Refer to
GI-41, "Intermittent Incident"
NO-2
>> Confirmation after repair: Inspection End.
Diagnosis Procedure
INFOID:0000000010417012
1.
CHECK CONNECTOR
1.
Turn the ignition switch OFF.
2.
Disconnect chassis control module harness connector
3.
Check the connector for disconnection or looseness.
4.
Check the pin terminals for damage or loose connection with harness connector.
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> Repair or replace the malfunctioning parts, securely lock the harness connector, and GO TO 2.
2.
PERFORM SELF-DIAGNOSIS 1
1.
Connect chassis control module harness connector.
2.
Perform “Self Diagnostic Result” for “CHASSIS CONTROL”.
Is DTC “C1BB6-00” detected?
YES
>> GO TO 3.
NO
>> INSPECTION END
3.
CHECK FUSE
1.
Turn the ignition switch OFF.
2.
Check that any of the following fuse is not fusing.
DTC
Display Item
(Trouble diagnosis content)
Malfunction detected condition
C1BB6-00
IGNITION POWER SUPPLY
(ignition power supply)
Ignition power supply voltage of chassis control module is as shown below.
• Ignition power supply voltage: 16 V
≤
Ignition power supply voltage
DAS-264
< DTC/CIRCUIT DIAGNOSIS >
[CHASSIS CONTROL]
C1BB6-00 IGNITION POWER SUPPLY
Is the inspection result normal?
YES
>> GO TO 4.
NO
>> Repair the applicable circuit. And then replace the fuse.
4.
CHECKCHASSIS CONTROL MODULE IGNITION POWER SUPPLY
1.
Disconnect chassis control module harness connector.
2.
Check the voltage between chassis control module harness connector and ground.
Is the inspection result normal?
YES
>> GO TO 5.
NO
>> Repair or replace harness.
5.
CHECK CHASSIS CONTROL MODULE GROUND CIRCUIT
1.
Turn the ignition switch OFF.
2.
Check the continuity between chassis control module harness connector and ground.
Is the inspection result normal?
YES
>> GO TO 6.
NO
>> Repair or replace harness.
6.
PERFORM SELF-DIAGNOSIS 2
1.
Connect chassis control module harness connector.
2.
Perform “Self Diagnostic Result” for “CHASSIS CONTROL”.
Is DTC “C1BB6-00” detected?
YES
>> Replace the chassis control module. Refer to
DAS-312, "Removal and Installation"
.
NO
>> INSPECTION END
Signal name
Fuse No.
Ignition power supply
4 (10A)
Chassis control module
Ignition switch
—
Voltage
Connector
Terminal
M43
10
OFF
Ground
Approx. 0 V
ON
6.4 – 16 V
Chassis control module
—
Continuity
Connector
Terminal
M43
12
Ground
Existed
DAS
C1BB7-00 CONTROL MODULE
DAS-265
< DTC/CIRCUIT DIAGNOSIS >
[CHASSIS CONTROL]
C
D
E
F
G
H
I
J
K
L
M
B
N
P
A
C1BB7-00 CONTROL MODULE
DTC Description
INFOID:0000000010417013
DTC DETECTION LOGIC
POSSIBLE CAUSE
• Chassis control module
FAIL-SAFE
The following functions are suspended.
• Active Trace Control function
• Active Ride Control function
• Active Engine Brake function
DTC CONFIRMATION PROCEDURE
1.
PRECONDITIONING
If “DTC CONFIRMATION PROCEDURE” has been previously conducted, always turn the ignition switch OFF
and wait at least 10 seconds before conducting the next test.
>> GO TO 2.
2.
CHECK DTC DETECTION
With CONSULT
1.
Turn the ignition switch OFF to ON.
CAUTION:
Be sure to wait of 10 seconds after turning ignition switch OFF or ON.
2.
Perform self-diagnosis for “CHASSIS CONTROL”.
Is DTC “C1BB7-00” detected?
YES
>> Proceed to
DAS-265, "Diagnosis Procedure"
NO-1
>> To check malfunction symptom before repair: Refer to
GI-41, "Intermittent Incident"
NO-2
>> Confirmation after repair: INSPECTION END
Diagnosis Procedure
INFOID:0000000010417014
1.
PERFORM SELF-DIAGNOSIS
With CONSULT
1.
Erase self-diagnosis result for “CHASSIS CONTROL”.
2.
Turn the ignition switch OFF and wait for 10 seconds or more.
3.
Turn the ignition switch ON.
4.
Perform self-diagnosis for “CHASSIS CONTROL”.
Is DTC “C1BB7-00” detected?
YES
>> Replace the chassis control module. Refer to
DAS-312, "Removal and Installation"
.
NO
>> INSPECTION END
DTC
Display Item
(Trouble diagnosis content)
Malfunction detected condition
C1BB7-00
CONTROL MODULE
(Control module)
When a malfunction is detected in chassis control module.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст