Nissan Qashqai J11. Manual — part 145
LU-40
< REMOVAL AND INSTALLATION >
[K9K]
OIL COOLER
Inspection
INFOID:0000000010284216
INSPECTION AFTER REMOVAL
Check oil cooler for cracks and clogging by blowing through coolant inlet. If necessary, replace oil cooler
assembly.
OIL PUMP
LU-41
< REMOVAL AND INSTALLATION >
[K9K]
C
D
E
F
G
H
I
J
K
L
M
A
LU
N
P
O
OIL PUMP
Exploded View
INFOID:0000000010284217
for symbol marks in the figure.
Removal and Installation
INFOID:0000000010284218
REMOVAL
1.
Remove the following parts.
• Battery negative cable
• Undercover
• RH front wheel
2.
Remove right side splash cover.
3.
Remove drive belt. Refer to
EM-278, "Removal and Installation"
4.
Remove oil pan. Refer to
EM-296, "Removal and Installation"
.
5.
Remove rear oil seal retainer. Refer to
EM-331, "Disassembly and Assembly"
.
6.
Remove oil pump drive chain. Refer to
EM-331, "Disassembly and Assembly"
.
7.
Remove oil pump assembly.
INSTALLATION
EM-331, "Disassembly and Assembly"
.
1.
Oil pump drive chain
2.
Crankshaft sprocket (oil pump drive
chain)
3.
Oil pump
E1BIA0028GB
LU-42
< SERVICE DATA AND SPECIFICATIONS (SDS)
[K9K]
SERVICE DATA AND SPECIFICATIONS (SDS)
SERVICE DATA AND SPECIFICATIONS (SDS)
SERVICE DATA AND SPECIFICATIONS (SDS)
Periodical Maintenance Specification
INFOID:0000000010284219
ENGINE OIL CAPACITY (APPROXIMATE)
Unit: ·(Imp
qt)
Engine Oil Pressure
INFOID:0000000010284220
kPa (bar, kg/cm
2
, psi)
kPa (bar, kg/cm
2
, psi)
*: Engine oil temperature at 80
°
C (176
°
F)
With oil filter change
4.55 (4)
Without oil filter change
4.39 (3-7/8)
Dry engine (overhaul)
4.71 (4-1/8)
Engine speed
Approximate discharge pressure
Idle speed
More than 80 (0.8, 0.81, 11.6)
4,000 rpm
More than 340 (3.4, 3.46, 49.3)
Maximum pressure
520 (5.2, 5.3, 75.4)
PRECAUTIONS
LU-43
< PRECAUTION >
[R9M]
C
D
E
F
G
H
I
J
K
L
M
A
LU
N
P
O
PRECAUTION
PRECAUTIONS
Precaution for Liquid Gasket
INFOID:0000000010508728
REMOVAL OF LIQUID GASKET
• After removing the mounting bolts and nuts, separate the mating
surface using a seal cutter and remove the liquid gasket.
CAUTION:
Be careful not to damage the mating surfaces.
• In areas where the cutter is difficult to use, use a plastic hammer to
lightly tap the gasket applied area.
CAUTION:
If for some unavoidable reason a tool such as a flat-bladed
screwdriver is used, be careful not to damage the mating sur-
faces.
LIQUID GASKET APPLICATION PROCEDURE
1.
Using a scraper, remove the old liquid gasket adhering to the
gasket application surface and the mating surface.
• Remove the liquid gasket completely from the groove of the
gasket application surface, mounting bolts and bolt holes.
2.
Wipe the gasket application surface and the mating surface with
white gasoline (lighting and heating use) to remove adhering
moisture, grease and foreign materials.
3.
Attach the liquid gasket to the tube presser.
Use Genuine Liquid Gasket or equivalent.
4.
Apply the gasket without breaks to the specified location with the
specified dimensions.
• If there is a groove for the liquid gasket application, apply the
gasket to the groove.
• As for the bolt holes, normally apply the gasket inside the
holes. If specified, it should be applied outside the holes. Make
sure to read the instruction in this manual.
• Within five minutes of gasket application, install the mating
component.
• If the liquid gasket protrudes, wipe it off immediately.
• Do not retighten after the installation.
• After 30 minutes or more have passed from the installation, fill
the engine oil and coolant.
CAUTION:
If there are instructions in this manual, observe them.
PBIC0275E
PBIC0003E
EMA0622D
SEM159F
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст